How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
I'm bringing up ble_app_hrs as an eclipse project using gcc.
I'm running into an error in app_util.h, line 67:
#define STATIC_ASSERT(EXPR) typedef char static_assert_failed...
Hello,
I'm using the following setup:
nRF Connect SDK v2.9.0
B0 , upgradable secure MCUBoot, and application
Statically defined partitions in the partition manager...
I am experiencing issues configuring an SPI-based SD card interface on my nRF5340DK using NCS v2.7.0. The SD card is not initializing correctly, and I am receiving repeated...
I have two nRF52833 development boards: one is connected to the nRF21540 EK as TX (using BLE peripheral_uart), and the other is used as RX (BLE central_uart). My issue is...
Hello,
I recently updated to the "new" nrfutil tool and installed the nRF Sniffer according to the instructions. I programed the firmware and ran nrfutil ble-sniffer bootstrap...
Hi.
I am looking for help with software development for my Thingy91 project.
Project is very basic and I am ready to pay based on hour rate. It is very simple and beginner...
Hi support team,
I'm working with nRF52833 DK. installed the mobile app and desktop, but I wasn't able to connect to either.
Power switch ON, SW6 on DEFAULT. J2 connected...
Hi
The Blinky Programm only starts when I give the reset Go command via jlink commander.
At Power cycle nothing happens.
If i give the SOC an external Pin reset the...
We have written a Flutter app, which uses the Flutter-nRF-Connect-Device-Manager package to perform firmware upgrades on bluetooth devices that the app bonds with.
If iOS...
Hi,
I’m looking at starting a new design that would be based on the nrf52840, however it seems that the flash readout protection is now fairly broken on this device. Are...
Both myself and a colleague had an issue in the past 48 hours where upon launch we were prompted to install a new West workspace/SDK. In my case it "tricked" me into installing...
SDK: 2.6.1 (2.9 seems to give an HCI build error , undefined reference to `__device_dts_ord_135', when enabled CONFIG_BT_LL_SW_SPLIT, CONFIG_BT_LLL_VENDOR_NORDIC ?)
SOC...
Changelog for nRF Connect SDK v2.2.0 mentions that:
nrf_dm_high_precision_calc() now handles out-of-memory errors by returning NaN .
What exactly are the memory requirements...
We want to generate 8.200 MHz as I2S MCK with an nRF5340.
This could be achieved with 12.300 MHz ACLK as source for MCK, and then dividing by 1.5 in the Master clock generator...
Hello evebody,
I have problem with socket creation. I am trying to copy example of this tutorial:
https://academy.nordicsemi.com/courses/cellular-iot-fundamentals/lessons...
