Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hi !
I'm doing some testing on mqtt with the nrf9160 DevKit.
So far, everything is working with TCP and TLS and I would like to use WSS. I started with WS but I can't...
Hello everyone I'm doing my first steps so as to get things right from the start with a device based on the nRF52833 chip. My setup: PC <USB> nRF52840-DK <JTAG> CustomBoard...
Hello,
I am having a problem using DFU using the android NRF connect app. I have two separate projects that use the OTA DFU. These two projects have the same DFU code...
Now I want to construct a mesh network in an intermittent environment. You know the device will power off and power on frequently, I need to store the communication statin...
Hello All,
I have referred the reference example code to suit my needs. Below is my code,
Code is stuck at waiting for event. Didn't get callback with oversamping of...
Excuse me:
The client made a keyboard with nrf51802.，It has been mass produced。The customer reported that the keyboard and MacBook were connected and bounding before opening...
Hi,
We have observed that in areas of poor lte connectivity, the client_inti() works well but the mqtt_connect() takes a couple of minutes and times out.
I need to change...
Hi,
I'm compiling a piece of code that uses USB CDC ACM from a .cpp file, and I stumbled on the compiler complaining about out of order initializers in app_usbd_cdc_acm_internal...
Hi,
I'm trying to use Zephyr's 'http_client' library in Asset Tracker V2. I have included 'net/http_client.h' in main.c and have set 'CONFIG_HTTP_CLIENT=y' in prj.conf....
Hi,
I want Windows PC to communicate with nRF52840 dongle over USB full speed.
Are there sample of Windows software(likes API) and nRF52840 dongle ?
I want to realize...
Hello,
What is the limitation of the total current we can source/sink at the same time in multiple pins for low Vdd?
I could find a similar question (and answer of 15mA...
Hello there, I am working on a customized nrf52832 board. For the limited size, the 32kHz crystal is not install because I think the clock from 32khz crystal can be replaced...
Hi all
I want to do a device firmware update via the bootloader, and I am unable to do so, as all attempts end with a disconnect from my Android phone (Pixel 4a). I can...
Hello!
Hardware: nrf52840 IDE: Segger Embedded Studio SDK: nrf5 SDK 17.0.2
I've been having issues with receiving USB HID IN reports on Android. If I send at an interval...
I'm trying to debug a usage fault in my NCS project using an nRF52833 DK. I can't seem to select the logging backend for coredumps. I have the following lines in my prj.conf...
