Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Hello.
I'm working with nrf52833 custom board and S113 softdevice for Buttonless DFU.
The pieces of information below are my FLASH & RAM address settings.
(Reference...
I'm trying to duplicate the boot behavior of a Thingy91 on a custom board, i.e. SW4:BOOT and SW3:BUTTON on power up, but the switches available use different IO. I'm wondering...
Hello, I am pretty new to using the Nordic products and was wondering if there is a simply way to write a text file from the nRF52840 to a pc. The system is required to log...
Hi Guys,
I know there are a lot if topicks about issue with "sd_softdevice_enable". I read them all and nothing help me. I'm using Eclipse IDE.
Im using a nRF52840-DK...
Hello,
I have recently switched my OS from FreeRTOS to embOS. I am now replacing the SDK files so my project will not be using FreeRTOS. I replaced the file app_timer_freertos...
hello,
I am trying to learn how to use the nrf52480 dongle and am trying to run the ble_connectivity example. I built it using Segger as is, no changes from the pca10059...
Hi!
I'm trying to sniff BLE advertising traffic using nRF Connect for Desktop on macOS and a nRF52840 Dongle.
I am running nRF Connect Desktop 3.8.0 on macOS Mojave 10...
I have done everything to install the VS code, installed Connect, Toolchains, SDK, Seggers etc. as in the help, but this is the result in VisualStudio Code:
It just keeps...
Hi,
The following code has been working fine since it was taken from the examples (NRF52840).
We wanted to remove the app_usbd_event_queue_process() so we enabled these...
Hello,
I have beacon advertiser and scanner. Scanner is scanning the devices from around. But its not scanning the device that i used for advertising. On the other side...
Dear Sir,
for my nRF52840 application made with the SDK v17.0.2 and S140 Softdevice I'm adding the peer module to a peripheral device example (UART with SAADC with timer...
I was trying to create my own sdk_config based on "$NRF_SDK/config/nrf52840/config/sdk_config.h".
I noticed it contains both the "NRFX" config and "Legacy" configs.
For...
I would like to change the GAP_DEVICE_NAME defined in nrf_mesh_config_app.h by DIP switch. like "nRF5x Mesh Light 1" or "nRF5x Mesh Light 2"
I have modified the light_switch...
