Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hello,
Is there a particular test Nordic recommends to screen for latent failures in the BLE circuit? If one has access to an Anritsu MT8852B tester with Direct-Test-Mode...
Hi,
I am updating SDK version from 15.0 to 17.0.
In many examples PM_FLASH_BUFFERS was changed from 2 to 4? What is the meaning of this change? We have one peer always...
While exploring documentaion and trying to learn more about the DFU (and bootloader settings), I found info on how to generate the bootloader settings , which also explains...
I want to measure voltages at all 8 channels but when I am enabling all channels its sending the values once only and after that its not sending anything, my requirement is...
Hi,
We are aware that i2s internally includes hardware double buffering to ensure that the audio is continuous.
Is there any way by which we can avoid double buffering...
Hello,
I developed board with NRF9160 chip and I am facing issue with "at_cmd: Failed to open AT socket (err:-12)", i am not able to communicate with modem. It is not...
Hi
Can I not modify the param the radio project example,and let it run on IEEE802.15.4-2006?
and the demo example run on 2.4GHZ?
I modified two params:
NRF_RADIO-...
Hello,
I'm using nRF52480 Dongle. I executed an Erase All from SEGGER Embedded Studio. My project still works but the LEDs are not blinking anymore. The only way I can have...
Hello nRF Team,
we are using nrf51822 for one of our product. We have implemented firmware update functionality using a secure bootloader library.
After loading the soft...
Hi, I want to distinguish whether the USB is connected to a PC or a power adapter.
For my application, FATFS still needs to work when connected to a power adapter, so it...
Hi Nordic,
Why I cannot directly use segger's "Build and Debug" to download file to nrf52832, after I modify some code?
After I use nrfGo Studio first to program the...
Hi, in the past, there has been discussed several times whether a peripheral can advertise even when it is already connected/bonded. It turned out it could be possible, however...
Hi, We are working on multiple product based on different MCUs (nRF52832 and ESP32). We would like to use the same Nordic BLE DFU for both of the products so that we would...
Planning to run Packetcraft LEAUDIO stack on nRF52840-DK. This is for evaluation and later on for some development on top of it.
Will it be supported. or is it must to have...
Hi,
I am trying to figure out how serial handling works. Specific questions bolded below. To the best I can see, what I think happens when transmitting is:
NRF_SERIAL_DRV_UART_CONFIG_DEF...
