Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Hi
I am working on a project which uses distance measurement config for multiple peripherals with long range.
Our plan is to support DM for up to range 25m and we observed...
I want to achieve time synchronization over a wireless connection with sub-microsecond latency. While PTP (Precision Time Protocol) can provide nanosecond-level accuracy on...
Hi, Nordic Bluetooth Controller Teams, I have a question. I see that the Aux offset of Bluetooth extended broadcast on NCS is fixed at 330us. What is the consideration behind...
Hi,
Is there a Zephyr sample project on QSPI with nRF52840? What I want to do is to write/read to an external flash (W25Q16JVSNIM).
Thank you
Best regards
Dav...
Hello,
I work on a thingy52 since few weeks with a nrf52832 SoC. When i'm turning it on and connecting it to my computer, there is no led turn on and it is not detected...
Im currently working on BLE SMP DFU on Nordic52840DK (Connect SDK v2.7.0) based on this example:
https://github.com/hellesvik-nordic/samples_for_nrf_connect_sdk/tree/main...
Hello everyone,
I am working on a project with a Thingy91 that has an nRF52840 and an nRF9160 , and I am trying to read the battery level. I want to measure this battery...
In ticket Case ID 290251, Torsten Rasmussen provides the following advice to ensure that the toolchain corresponding to the SDK is used to build the SDK (this applies to nrfutil...
I am lab testing Nordic's DECT-NR+ (DECT) for a new factory automation application; I am using the hello_dect sample application from the PHY webinar demo, I am trying to...
I made a custom board, uploaded the Arduino bootloader and was flashing the firmware with Arduino I used it without any problem with revision 2 But when I use revision 3 chip...
Hi! I'm working on the firmware part that needs to perform operations on the same variables both inside GPIO IRQ and the software timer callback. So, there is a need for a...
Hello, I want to send data from peripheral devices to central device. My peripheral device code is based on "ble_peripheral_uart" sample and my central device code is based...
Hi, I'm working on developing a UWP app that can detect any or compatible Nordic devices. let's say a device has BLE capabilities, then through the desktop app i should be...
I have both a nRF5430DK and a nRF9151DK (or 9161). If I wanted to develop a solution with both BLE and LTE, how do I set up a DK environment for them to work together? Do...
Hello,
In my experimentation to update advertising data during runtime, I am following the example @
It is using the ble_advertising.h library module
However I would...
