I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hello.
Since nRF Connect SDK v3.0.0 has been released, I am testing the sample program . It is a sample I have frequently used from previous versions. The provisioning with...
hi support team,
DTM is not able to build thingy53, do we have any support for this board? or any instructions for it?
radio_test is also not able to build thing53.
...
Hi everybody.
I'm developing my own board based on nRF52840 SoC. I'm using nRF Connect SDK 2.6.1. I need to log the environment events by date & time details on QSPI using...
Hi!
We are developing home automation light control mesh products.
We use nrf52832 DK (PCA10040), with nRF Connect SDK Toolchain v2.7.0 and nRF Connect SDK v2.6.1
We...
hi,
After upgrading mcuboot from NCS 2.6.1 to NCS 2.9.0, the upgrade file is downloaded, and the device restarts and runs normally. The mcuboot version number and active...
Hello,
I have an nRF52840 based custom board (myboard, NCS2.70)
its partitions node closely follows the nRF52840DK dts file:
both have &flash0 in the /chosen group...
I have a nRF54L15-PDK kit. I also have the latest v2.9.1 SDK and toolchains installed using the VSCode plugin (also latest).
I use the plugin to create a new application...
I am new to designing with Nordic microcontrollers. I am at the point in my design where I am laying out connections to the microcontroller and setting up which pins will...
when I tried to add a device to nrf cloud, I am getting an error message 40101
My device is nrf9151dk with IMEI 359404230049133 and HWID 374155 I believe I might have registered...
I am exploring the possibility of using ncs v2.8.0 for Mesh with Coded PHY on the nRF52840dk/ nRF52840 board . I know this is not officially supported.
I started with the...
Dear,
I’m using nRF Connect SDK 2.7.0 with BLE Mesh and wondering how to adjust the TX power dynamically. When setting the TX power using a predefined option like CONFIG_BT_CTLR_TX_PWR_PLUS_8...
NCS 2.7.0
nrf52840
I'm currently porting software that was originally developed for nrf52832 on NRF5 SDK to run on Zephyr. I am currently on a deadline to delivery a prototype...
I've tried to follow the exercises from the Bluetooth Low Energy Fundamentals course. When I try to run the solution for lesson 3 exercise 2 I get the following error messagen...
Hello,
I have some previous code that ran using BT mesh. I then updated SDK's to 2.9.0 and I am now having issues provisioning devices. I am using the BT Mesh Provisioning...
Dear Nordic-support,
I am trying to use the modem_battery_low_level_handler and modem_battery_low_level_set(), but I think there are two different ranges for the battery...
