This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I am working on project where my requirement is something like... Device will advertise and it gets scanned by its own scanning.
What I have done so far......
Hello.
We are migrating from SEGGER Embedded Studio (SES) to IAR Embedded Workbench (IAR). At that time, an error occurs that "__ICFEDIT_region_RAM_start__" is not defined...
I want to select the nRF52 series SoC as our product platform. I have a use case in which I want to get the optimal channel map and I find the "sd_ble_opt_get()" function...
I have taken over a older (5+ years) project that uses Gazell, but it didn't use the Gazell link layer to do wireless pairing. We were looking at shifting to SDK 12.3 (last...
Hi,
I am using the CAF BLE components to use bluetooth on the nRF52840, which I control over HCI via the nRF9160. This is all working.
To use the CAF advertising component...
Hello Nordic DevZone, My name is Ted, and I'm having some difficulty with a recently installed Nordic / Zephyr SDK and toolchain. On 2021-07-24 I downloaded and installed...
I'm trying to read the memory off of a BT840F, which I'm hoping to do via a debugger. I've read that a tag-connect cable can be used to connect from a pcb to the debug out...
Hi,
I tried running the "chat" example on two NRF52833DK boards, one as a sender sending a "Hello World" message every 500 milliseconds, the other as a receiver, and found...
Hi,
I have an issue when I migrate my app from nrf52 sdk v16 to v17.
I have setup an app with an uart communication, an app timer and a watchdog. All off these (uart and...
We are using the Libuarte - advanced UARTE driver and sometimes see crashes in the uart_evt_handler code in nrf_libuarte_async.c when it gets a NRF_LIBUARTE_DRV_EVT_RX_DATA...
I am interested in developing a Cloud Driver that communicates to my own servers over HTTPS.
Cloud API documentations state that a driver needs to implement a set number...
Can I UART/SPI/I2C on any pin of NRF52832?
- Can I UART/SPI/I2C on any pin of NRF52832 which is mentioned general-purpose I/O pin ?
- Is there any limit on how...
Hi,
Actually we are searching for a chip which has more than one UART channel for communication.
Can we define more than one UART channel with GPIO configuration? Is it...
Hello, I am currently using the TWI in non-blocking mode, however I frequently run into the issue where the code gets stuck on nrf_drv_twi_tx. function at the return result...
