After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
Hi,
I want to use external power (battery) and USB power together.
If USB is not connected, I want to supply it with battery power, and if USB is connected, I want to...
Dear HW engineer,
I have ordered a few custom boards with nRF52820. As recommended by the datasheet, I have used 12pF load capacitors for both HF (32MHz) and LF (32kHz)...
Hello
I use nrf52832 and SDK v17.
I'm conducting various tests on Bluetooth. And I faced a lot of new problems. I erased a previously saved bond from the Android nrf connect...
Hi
After successfully testing nRF9160 SLM app. we plan to use nRF9160 with UDP and LwM2M protocol in our smart devices. We also have our private cloud server where all the...
Im new using Nordic devices , I am trying to using nrf52840DK to locate nrf52840 dongles using the direction finding method , how can I connect the dongles to the DK and build...
HI,
Is it possible to update modem firmware from 1.2.0 straight to 1.2.2? Or is it the only way to first update from 1.2.0 to 1.2.1 and then to 1.2.2?
Regards, Tero
Hello
I'm testing the firmware using the BLE. When I upload, I can see that the board is working. Also, I don't think there's a problem with running each line of debugger...
I'm trying to build the blinky zephyr sample for nRF Connect SDK and get the following failure:
Creating solution blinky.emProject
/usr/local/bin/cmake -GNinja -DBOARD...
How can I, from the pc-ble-driver API, send an insufficient authentication request without configuring a characteristic to be secured?
I am testing out new standards. One...
Hello, Nordic community,
I want to implement OTA using Thread with nRF Connect SDK.
Is there any sample code or reference this can be done with Thread?
Thanks,
...
Is there a limit to the number of handlers that can be registered using NRF_PWR_MGMT_HANDLER_REGISTER? I can't seem to get any more than 3 to be called, changing NRF_PWR_MGMT_CONFIG_HANDLER_PRIORITY_COUNT...
Hi--I'm part of a research group that will be using the Thingy 52 to record environmental variables, and we will need to transfer information to a cloud server using a satellite...
HI，ALL：
How to setup TX mode in example PRX，and so,how to setup Rx mode in PTX example. I use esb_init() of example PTX in example PRX， But when I fill data in fifo, it...
HI，ALL：
when using ESB example ,the transsmit waveform is below(in channel 3):
how to make it more simple,like that as below(other example in channel 3):
