We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hardware Setup:
nRF52840 DK: Serving as the BLE central device and I2S master.
PCM5102 DAC: Connected to the nRF52840 DK via I2S. The connections are:
LRCK (Pin 30...
Hi ,
For Battery operated devices, we are using NRF52840, and developing the firmware using Segger Embedded studio + NRF SDK. s140nrf52720, nRF5SDK1702d674dde
For our...
Hello,
I'm sorry to ask a maybe stupid question, but I'm a bit lost with the available boot loader options right now.
I want to setup an updatable and secure bootloader...
Hello,
I am using nRF9160DK, nRF SDK 2.8.0 with sysbuild and trying to enable image encryption trough sysbuild Kconfig options. I have set SB_CONFIG_BOOT_ENCRYPTION and...
Hi, After switching to a newer Zephyr version with the hardware model V2 I am struggling to build a BLE sample for the nrf5340 DK. It seems that the netcore image is not built...
Hi guys,
I'm working on a project with a custom board around nrf52832 chip and I'm trying to generate an 8MHz clock signal using the compatible "pwm-clock" on Zephyr.
...
Hi, I have encountered some problems:
hardware: nrf5340-dk
software:Visual Studio Code
ncs:2.5.0
sample: nrf\samples\bluetooth\direction_finding_central & direction_finding_peripheral...
SDK 2.1.0
nRF9160
Hi,
I recently configured a GPIO input in my project with an associated interrupt whenever it detects a high to low transition. The transition is...
Hi,
I am currently extending the NRF Cloud multi service sample, thus I am constantly reflashing my NRF9161DK during development. However today, my device fails to connect...
Hi,
While debugging an issue with reconnecting to our Azure server after the network is lost for some time, I found that azure_iot_hub_connect() returned a non-negative...
I tried to use `-Dmcuboot_DTC_OVERLAY_FILE` to use different mcuboot overlay for different builds but it always use all the overlay files in the folder.
The same way works...
This is a continuation of Case ID: 272157
That case resolved issues I had dynamically changing the device name (and having that new name show up in advertising).
It seemed...
I tested with an nRF52840 dongle, but it seems that nRF Connect for Desktop cannot scan long-range/coded PHY advertisements.
(I used this BLE long range peripheral demo...
Hi,
I’m currently developing an application for the nRF52833 that collects sensor data via SPI and sends it out over BLE using notifications. My primary goal is to achieve...
