But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Encountered an issue while programming the nRF5340:
It was working fine before, but after connecting to RTT, a pop-up prompted some encryption option which I didn't read...
Two days ago, I bought a set of ppk2. in the process of use, the host computer software prompts "Device must be programed do you want to procced?", when I click "yes", the...
https://github.com/NordicDeveloperAcademy/ncs-fund/blob/main/v2.9.0-v2.7.0/l4/l4_e1_sol/src/main.c
The current logic uses i and j to calculate factorial.
for (i = 1;...
Hi:
I use sdk nRF5_SDK_17.1.0_ddde560. bootloader use examples\dfu\secure_bootloader\pca10056_uart_debug.
It cann't enter the application.
But If I use examples\dfu...
Hi,
I'm currently trying to write a simple Wi-Fi driver code that can connect to my Wi-Fi network. I'm building for the nrf7002dk_nrf5340_cpuapp and am using NCS v2.5.3...
I want to use the radio test code from the nrf example library to tune the nrf52833 on a custom board. I managed to build and flash the project, but when connecting to the...
Hi,
I have been evaluating some Nordic Semiconductor products for the past week. They look great.
I am using the nRF5340 Dev Kit, along with Visual Studio Code on...
As stated in the title, when I set CONFIG_CHIP_FACTORY_DATA_BUILD to n , the following compilation error occurs.
However, if I keep it as y , the MCU fails to function...
Is a Zigbee Direct SDK available for Linux which could be used to allow it to act as a Zigbee Virtual Device (ZVD) using Bluetooth LE?
I am particularly interested in the...
I am measuring latency using the nrf5340_audio with SDK 2.8.0. The measurement points are the analog input on the gateway side and the analog output on the headset side. I...
Hi!
I am using v2.6.1/nrf/samples/bluetoothdirection_finding_connectionless_tx/rx sample, and NCS v2.6.1 for AoA. I made some modification on the rx side to stream I/Q data...
Hi support team,
I'm currently developing a project that requires enabling FCB (for dps to Azure IoT Hub) and LittleFS to store data on an external flash. However I cannot...
academy.nordicsemi.com/.../
The comparison of "increment_count + decrement_count != COMBINED_TOTAL" happens after test_mutex unlock. It is possible that between comparison...
“'\x03\x01\x00\xDB\xDC\x00\x00\xDB\xDD\xFF\xD5\xD1\xC0”An error occurred during the transfer of the bin file, and the packet was returned when the crc was fetched. What should...
