Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hello to all,
I have a question about parsing zigbee commands when they present a payload.
In the Window Covering device I use the define "ZB_ZCL_WINDOW_COVERING_GET_GO_TO_LIFT_PERCENTAGE_REQ...
Hi support team,
I'm learning about distance calculation based on time of flight. I only have nrf52832DK here but i wanted to try. I'm looking for an example of getting...
Hello,
Power Profiler v3.1.3
Windows 10 Home 21H1
On Data Logger tab and , regardless of if a PPK2 has been connected or not, and regardless of any of the values...
Hello,
I have been using the nRF52840 DK board and have designed a PCB based on it. I made a previous post asking some questions before designing the PCB, so this is a follow...
I have developed an application for the nRF52-DK (nRf52832AA) and am now in the process of porting the application to my custom hardware. My custom hardware utilizes the nRF52832AB...
I'am working on nrf52840 and base on a sample hci_spi. I use spi1 and tried several different pins, they all works fine.
but when i disable qspi and try to use the pins...
Hi,
I am doing a simple thing with string formatting:
sprintf(tmp_str,"%d.%d.%3d", version.major, version.minor, version.patch);
The version structure has values { 0...
Hi, This time I'm on NCS 1.3.0. Board definition is derived from nrf5340pdk_nrf5340, with some minor variations, and it is out-of-tree. I think it is OK. Since I moved also...
Hi there,
How can I manually awake my advertiser which is in low power mode, to start advertising and get it back to sleep after it advertises certain number of packets...
Hi,
I'm having some troubles with the Thingy:91 because it became unresponsive after I flashed the device with the mqtt_sample firmware.
I built the mqtt_sample with...
Hello everyone,
I am having an odd problem. I am using an SoC based on the nRF52832 (the ISP1507-AX). So far I had been using ncs v1.6.0-rc2 during development. Recently...
hi support team，
customer have one question, when 9160 attach the network, which one does it choose (the best signal or the first base tower discovered)?
especially when...
Hi Dev Team,
I am developing the weight scale product using nrf52840 development board. We connected the nrf52840 using the nrf connect app ( Provided by nordic).
Now...
Hi, I'm using the BC805M EK (nRF52805) . I would like to pull up pin 20. Here is my configuration in pca10040.h. However, pin20 cannot be pulled up. It's always pulled down...
