i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
sdk 17.0.2
IDE - segger embedded studio
For the below given code, " pin " is not updating when GPIO goes high when optimization level is kept "Level 3 for more speed"...
I'm using the serial_lte_modem application from Tag v1.5.0-rc1, on the nrf9160dk evaluation board to make a secure connection to google.com but it returns #XHTTPCCON:0.
...
I have flashed DFU OTA bootlaoder to my nRF82540 DK. (C:\nRF5_SDK_17.0.2_d674dde\examples\dfu\secure_bootloader\pca10056_s140_ble_debug)
It shows the two LEDs 1 and 2. ...
Again no where I can find to put this. Also under documentation as a tag you need another option to select, e.g. SDK
Anyhow, When I try and search the documentation the...
I think I've found a bug in the power management that occurs only when a softdevice and the debug interface are active. In SDK v17.0.2, nrf_pwr_mgmt.c lines 417-429:
The...
Hi,
We using nRF Connect SDK,
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/libraries/zigbee/lib_zigbee_shell.html#zigbee-shell-command-list
We founded...
Hello,
I am working on nrf52833 using the soft device s140 ble with csence enabled.
but the cap button has problems to detect signal, what is the
THRESHOLD_BUTTON...
Hi,
I'm using nRF5 SDK, use original build. No change anything. Just enable the Zigbee CLI as Coordinator.
After tested with various devices, found out a lot devices...
Hello. I am developing using nrf52832 (S132 v7.0.1, SDK v16.0.0).
I use whitelist to store bonding information. Is there an upper limit to the number that can be stored...
Hi,
I am trying to configure a GPIO pin P0.21(as this is exposed pin on Thingy:91) from nRF9160 on Thingy:91.
I am using nRF Connect SDK 1.4.1 with Nordic version of SES...
Hi,
I am evaluating the LTE modem demo. I downloaded the demo binary firmware images a few weeks ago. Today I installed the LTE Modem demo into my dev kit. It connected...
I want to develop a 2.4G mouse Dongle and have used NRF52840 and SDK 17.0.2. When I have used USB or ESB one by one - all is Ok. But when they are used together - usb driver...
