Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tried running the "chat" example on two NRF52833DK boards, one as a sender sending a "Hello World" message every 500 milliseconds, the other as a receiver, and found...
Dear Support
I try to use Watchdog on nRF9160 DK.
I found the sample ..\v1.5.1\zephyr\samples\drivers\watchdog
From there I add to my prj.conf
CONFIG_WATCHDOG=y CONFIG_WDT_LOG_LEVEL_DBG...
Hi,
I wanted nRF5340 capable of reporting the VDD under-voltage event causing a pin reset through a dedicated voltage monitoring IC. For this reason I put a Flip-Flop for...
I am currently experimenting with moving my request for PSM mode into the "lte_lc_init" routine so that it is configured before the modem is moved to Normal mode.
With...
Hi!
I have previously tested connecting the nRF9160-DK to an external MCU to act as an Serial LTE Modem as per the application description. And it worked
fine. Since then...
Hello.
I use nrf9160 and download ota with aws.
After my board download successfull and return event FOTA_DOWNLOAD_EVT_FINISHED, I do system(0) to reboot.
But it can...
Hello,
what is the raw frame to get a good NRF Temperature Service UUID BLE ?
I didn't get custom data (temperature), just the service uuid 0x1809
Here is my raw frame...
Hi
Since a recent Android security update, I am experiencing issues with my 'Just Works' device based on NRF52832. Prior to this Android update, once paired, I would receive...
I am trying to connect ,disconnect and connect using nRF dev kit with one of the BLE product. (using PC-BLE-DRIVER-PY)
Steps:
1) Open driver connection:
self ...
hello Nordic
i am using nrf52832 soc, sdk 16.0, s132 v7.01
my app requires the s132
i am trying to understand the bootloader issue, not so successful on that unfortunately...
We are developing a product based on nrf52840. The product will always be configured as a BLE peripheral. We need to be able to use OTA for both SoftDevice & Application code...
Hi, all
I'm going to develop a crypto application, and tested on nRF52840 with nRF5_SDK_17.0 CC310 run-time library.
there are a need is compute public key from a known...
Hello,
We are currently using the 0.27 and the 0.26 PINs of the nRF52840 for I2C communication as suggested in the sample code. But we need to use the P1.12 and P1.14...
