When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
Now, I have a provisioner (based on the provisioner example of the mesh sdk) and I want to unprovision a specific device.
I have tried to use "config_client_node_reset...
Hi,
I have three nRF52840 DKs
I am trying to connect two of them as peripheral devices( that implement the ble_app_uart example)
to the third nRF52840 central device...
Hi guys new to the Nordic family of devices, but can the thingy91 provisioned on a third party cloud platform other than the nrfCloud? Also can I use a different sim-card...
While migrating to the latest nRF5 SDK (17.0.2) and nRF for Mesh SDK (5.0.0) , I've noticed that they ship with Softdevice 7.2.0 .
The latest s132 Softevice available for...
Hi,
I understand that scan request allows the broadcaster to send additional advertising data. Does it send the additional data via data channels? Is it related to secondary...
SEGGER ver 5.50d
nRF52840
I'm trying to find a way how to use the STL library with GCC compiler. I know that SEGGER is not fully supported STL library (a basic stl library...
Hi,
We are developing a solution using nRF52 and nPM1100 using nRF5 SDK 17.x? I was wondering if there is a software library already written for the nPM1100?
Thank you...
Is it possible to change the smartbasic firmware? and if I want to return to that firmware how can I doit?, and last one, if I use de nordic SDK with the DVK BL654, does it...
Optimization level is set to "Debug". Tried to change it to one of the Levels, however then firmware does not run at all. Debugging Level is set to Level 3.
Can it be other...
I want to develop the nRF series at segger embedded studio for the first time. But I tried the following homepage to install manually. www.nordicsemi.com/.../Segger-Embedded...
NCS(nRF Connect SDK) is a good environment to develop nRF52,but it seems not stable until now.
I want to use NCS(nRF Connect SDK) to develop my project ,and met some unknown...
Hi Supporter,
I use apptimer in proprietary_rf gzll, I used as below ,but it doesn't work.
1) app_timer_init(); ,here I ennable the RTC1 in the sdk_config.h
2)app_timer_create...
Hello NRF ,
I have been using NRF9160 DK GEN-1 board for NB-IOT and GNSS tracking and able to configure my network SIM as well as the NRF cloud .
I have used SDK 1.4.2...
Hello There,
Basically I just want to get Sensor data like (Temp Sensor) who already connect to Arduino and I get it , So I just want that data to nRF9160 over UART in...
