Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I have some of peripherals at 1.8V and some at 3.3V that I'd like to run off the nRF5340. Is there a way to selectively set which interface is in a specific voltage...
Description:
We'd like to extend our existing bootloader. It currently supports UART transport and we want to retrofit a bootloader that also supports OTA via BLE. On merging...
I am testing the nRF9160 DK. I would like to know which SIMs are available in Japan.
I have confirmed that Sakura's Secure Mobile Connect SORACOM(Plan-KM1) works.
I'm...
I'm sorry if this has been answered somewhere else, but I couldn't find a thread that specifically addressed this.
Looking through the Modem FOTA options there is the...
Hi,
I'm working on a design with nRF52840 on PCIe Mini Size card. Since there is no VBUS rail on PCIe connector and I need a communication via USB, is it possible to bypass...
I see that I can USE BT MESH in an application . Can I encrease the number of advertisingh channel adding some secondary advertising channel?
May I do that in this way ...
Hello,
I come to you because I did not find the information on the web about sending MQTT data. I send a buffer of size 1408 with MQTT but I see in the configuration that...
Here is a screenshot of my current debug session. I cannot figure out why this if statement is failing. I have circled the relevant information. Even the disassembly indicates...
Hello,
I am trying to debug and develop in the net core of the nRF5340 and am having trouble flashing and debugging from SES.
I started by following the guide posted here...
Hello,
My board is connected to Gyro, Magneto sensor.
And board is sleep and wake-up by GPIO.
It usually works well. But time to time after wake-up from sleep mode...
Good Morning!
I try to update the modem firmware of a nRF9160 chip.
When I connect it with the nRF Connect v3.6.1 - Programmer (v1.4.10) and try to update the modem with...
Hi all
For the nRF52832, the total maximum sink and source current is recommended to be 15mA in this devzone entry .
Unfortunately, it seems like there is still no value...
I want to add an external button that mimics the properties of the buttons in the nRF52 DK. I read that the switches are all active low, so I assume that this means they are...
Hi,
in peer_manager.h and id_manager.h the docs say a function can return
BLE_GAP_ERROR_WHITELIST_IN_USE
But the error code is called
BLE_ERROR_GAP_WHITELIST_IN_USE...
Hello,
I have an nRF52840 on a custom board. The nRF52840 has been pre-flashed with the Adafruit UF2 bootloader for early development exploration. As the project moves forward...
