Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
sdk 17.0.2
IDE - segger embedded studio
For the below given code, " pin " is not updating when GPIO goes high when optimization level is kept "Level 3 for more speed"...
I'm using the serial_lte_modem application from Tag v1.5.0-rc1, on the nrf9160dk evaluation board to make a secure connection to google.com but it returns #XHTTPCCON:0.
...
I have flashed DFU OTA bootlaoder to my nRF82540 DK. (C:\nRF5_SDK_17.0.2_d674dde\examples\dfu\secure_bootloader\pca10056_s140_ble_debug)
It shows the two LEDs 1 and 2. ...
Again no where I can find to put this. Also under documentation as a tag you need another option to select, e.g. SDK
Anyhow, When I try and search the documentation the...
I think I've found a bug in the power management that occurs only when a softdevice and the debug interface are active. In SDK v17.0.2, nrf_pwr_mgmt.c lines 417-429:
The...
Hi,
We using nRF Connect SDK,
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/libraries/zigbee/lib_zigbee_shell.html#zigbee-shell-command-list
We founded...
Hello,
I am working on nrf52833 using the soft device s140 ble with csence enabled.
but the cap button has problems to detect signal, what is the
THRESHOLD_BUTTON...
Hi,
I'm using nRF5 SDK, use original build. No change anything. Just enable the Zigbee CLI as Coordinator.
After tested with various devices, found out a lot devices...
Hello. I am developing using nrf52832 (S132 v7.0.1, SDK v16.0.0).
I use whitelist to store bonding information. Is there an upper limit to the number that can be stored...
Hi,
I am trying to configure a GPIO pin P0.21(as this is exposed pin on Thingy:91) from nRF9160 on Thingy:91.
I am using nRF Connect SDK 1.4.1 with Nordic version of SES...
Hi,
I am evaluating the LTE modem demo. I downloaded the demo binary firmware images a few weeks ago. Today I installed the LTE Modem demo into my dev kit. It connected...
I want to develop a 2.4G mouse Dongle and have used NRF52840 and SDK 17.0.2. When I have used USB or ESB one by one - all is Ok. But when they are used together - usb driver...
