I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hello, I want to ask a question. We have a project that needs OTA function. There are two Bluetooth devices A and B.
1. Both A and B are central_and_peripheral
2. A's...
I want to check for an RX timeout after sending a TX.
I am puzzled on how this comes about.
As best I can tell I have enabled TIMER3 for the timeout.
I have created...
I'm trying to create a user defined HCI command for nrf52840 over the Zephyr APIs to be used against Bluez stack on Linux.
I've enabled the CONFIG_BT_HCI_VS_EVT_USER=y....
Hello,
I am trying to accomplish sending a simple ON or OFF command to the coordinator. Is this possible to do?
I have a router device with these Clusters:
It...
I have been converting my TWI calls to be asynchronous by specifying a twi_handler, but my NRF52840 does not sleep during the TWI calls.
I use SDK15.3 and s140 softdevice...
So this is my understanding of the programming process of an external board using the DK.
Pins from table 1 here: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fug_nrf91_dk...
Hi,
I want to develop DFU using BLE. I have started with test image given in the example folder.
I have nrf52480 device , using S140 softdevice. I have followed these...
I am unable to see advertisement on the nrfconnect app, when using BLE_GAP_ADV_TYPE_CONNECTABLE_SCANNABLE_UNDIRECTED
However, when using BLE_GAP_ADV_TYPE_NONCONNECTABLE_NONSCANNABLE_UNDIRECTED...
Hello.
I am developing using nrf52832 (S132 v7.0.1, SDK v16.0.0) as a central and Android device (Bluetooth 4.2) as an advertisement.
During development, I was wondering...
Greetings.
We've been developing a product that uses BLE Mesh. We are currently using the Waveshare nRF52840 Bluetooth 5.0 Evaluation Kit for prototyping purposes. As far...
When I try basic usage of NRF Queue library I'm getting the following error:
Undefined reference to `nrf_queue_write'
SDK version is 15.3.0.
In sdk_config.h I've enabled...
Hi Support,
I have tried setting up my nRF52840 Dongle ( https://www.nordicsemi.com/Software-and-tools/Development-Kits/nRF52840-Dongle ) PCA10059 as explained in the steps...
Hi,
I've got the gaming mouse dev kit and I'm stuck trying to get it programmed using my nRF52840-DK. See my hardware connection image below.
If I leave the mouse power...
Hi. I am currently using a custom nRF52840 board.
I am able to connect and pair with both IOS and android via BLE. However, the IOS have some issues.
After 45 minutes...
