I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I have been trying without success to install either the v2.7.0 or v2.8.0 SDK onto my Windows 10 System. Every time/method I've used results in an error equivalent to
...
Hi,
SDK17, Softdevice S112, NRF52805 custom board.
I have baremetal bsp implemented but I am new to Softdevice and struggling a bit with an interface concept beween two...
Hey,
I'm using the nRF5340 and want to run the PTS test with the following configuration: The CAP initiator establishes two audio streams within a single connection to the...
Hello,
We are currently experiencing some unusual behaviour on our feather board (circuit dojo, nRF9160 chip) which we are seeking advice on.
Whats happening:
Device...
Hello,
I'm using NRFX PWM directly because I need something more custom than zephyr's PWM driver provides. I'm trying to understand what .pin_polarity field in the config...
Hello,
When I follow the steps to create a new standalone workspace application for SDK and Toolchain 2.9.0, and then add a new build configuration and build the project...
Hi,
I'm developing a system which needs to have near real time control (downlinks) and uplinks. I've into these 2 issues. Please note that I'm still a beginner with LTE...
Hi I tried to put descriptor on the characteristic recently and it didn't seem to work. Is there something wrong with that?
If I take the following code that adds...
Hi, I have a brand new nrf5340dk and the debug interface is not showing up when connected: I have other nrf5340s that work so I'm sure its the board specific.
Board label...
Hello,
Customer would like to know if part below:
NRF52840-DONGLE
Customer would like to know if there is any connector that Customer is able to use to the above part...
Hello,
I am relatively new to the nrf9161, but I am running into an error with my build.
'TFM_PERIPHERAL_DPPI_CHANNEL_MASK_SECURE' undeclared (first use in this function...
Hi there,
I intend to use pynrfjprog in development replacing another, older library. However, any call to the API which involves the nrfjprog DLL returns:
This is on...
Hi:
MCU: nRF52832
The device is powered by a battery. When the battery voltage drops to around 1.3V but is not completely depleted, if the device is charged at this time...
I am in the development phase of a Bluetooth based system design, which will be able to receive audio stream from any mobile device and play on the speaker, and also it would...
