Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
We are currently porting our code to the newest nRf5340 chip.
Everything goes fine when the target is secure (not ending with "ns" and not defining "CONFIG_TRUSTED_EXECUTION_NONSECURE...
Hi,
I am working on a device that has nrf52 as an additional BLE chip that does not run the main logic but provides UART over BLE to the application processor (NUS). In...
Hi,
I am working on the our customized board nRF52832 , interfaced with MAX30205 temperature sensor . I am advertising the data only when it reaches the below temperature...
Hello,
We are planning to use the accelerometer in the Thingy91, we have some inconsistent results when configuring/reconfiguring, we have 2 questions:
- When we, for...
Hey,
We've been having issues with a subset of a batch of devices produced recently, with an unacceptably high failure rate when switching to DFU from firmware (the switch...
Hi everyone,
Is there a function like APP_USBD_CDC_ACM_GLOBAL_DEF or APP_USBD_MSC_GLOBAL_DEF that allow to define a custom class?
I want to define a custom class using...
Hello there,
I am using the nRF52832 and I need to talk to 2 different UART based peripherals.
In order to do that I was thinking to use the libuarte module in time...
Hi
There are already several questions regarding UART clock source, e.g. that one for nrf52 where it is stated that the peripherial always take the 16 MHz clock.
Is this...
Hi, the nRF21540 FEM is out for quite a long time. However, there is still no direct support in NCS. Fortunately. some work has already been done. This PR introduces the FEM...
I want to add some logging to my nrf5340 net application and I'm having some troubles.
I have the following in my main.c: #include <logging/log.h> LOG_MODULE_REGISTER...
Its clear there is little interest in this DK compared to the nRF52 version. I got instructions for that platform that actually worked.
Not so for the nRF51 DK. But I am...
I am using FreeRTOS and some of the commands there have two flavors: for using in regular code flow and when are executed from an ISR, but in nRF SDK components and examples...
Hi All,
I cannot get the NRF_LOG messages via RTT to the debug terminal in SES or RTT Viewer.
My setup: HW: PCA10040 SDK: 17.0.2 Project: nRF5_SDK_17.0.2_d674dde...
Hi,
I followed all the steps to get NCS up and running with SEGGER Embedded Studio. However, when I try to open an example, I get this error:
Including boilerplate ...
