Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
Hello,
We have a problem that affects a few devices (< 0.1 %) in mass production. The devices are flashed, boot up and pass tests and get shipped to customers. Some customers...
1. all files were successfully attached
2. there is no syntax error, there are only warnings
3. Please help me to resolve this problems as soon as possible.
Good day everyone !
Can thingy 52 itself be used as a location tracker, from Received Signal Strength Indicator(RSSI) . Does it have this function ? If it does, may i...
Hi all,
First of all, this is a new field for me, so I'm quite a beginner here. I'm connecting my ESP32 to wifi and I want to send somehow the IP it connects to, to the...
Hello,
In my application (SDK, 16.0.0, nRF 52840) I need to enable the DFU service after initialization, which I do by exposing a custom service "DFU enable". This in turn...
I'm currently using Zephyr with Nordic Segger v5.50c.
Most of the code uses NRF_LOG, NRF_ERR statements which are printed to the Nordic Segger terminal.
I also configured...
Hi,
We are trying to update the S112 softdevice on nrf52811 over serial DFU but it's not working and throwing the below errors.
We are using nRF5_SDK_17.1.0 and soft...
Goodday,
For some reason my nrf Connect Programmer stopped working after doing the latest updates. To test I took a brand new dongle, Programmer picks it up but does not...
Hello, i have send my program with my DKnr52840 on my module 805, (the example peripheral Uart) now i would like to make my com with putty or other software but i'm going...
Hello,
The company I work for uses an nRF52840 PCBA for one of its project. During production, the board will be placed under test using a custom-built fixture. Due to the...
Hi,
For my application I am supposed to evaluate if nordic SPIM & SPIS drivers are working on interrupts..? In the driver file "nrfx_spim.c" I observed the below code...
Hi,
I have some questions regarding DFU:
Does it have its own BLE hardware?
Does it have its own processor? Or it's part of the main one?
Can we synchronize between...
Hi all,
struct spi_config {
uint32_t frequency ;
uint16_t operation ;
uint16_t slave ;
const struct spi_cs_control * cs ;
};
in documentation, it says...
Hi I am recently working on Enhanced Shock Burst (ESB) protocol. where PTX and PRX
and
PRX will communicate upto 8 PTX
i have a question like how a single device will...
