Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
Hello, I bought the Bluefruit LE Sniffer - Bluetooth Low Energy (BLE 4.0) - nRF51822 - V3.0 from Adafruit Bluefruit.
So, I downloaded nRF Sniffer for Bluetooth LE 3.0 and...
Hi,
I am trying to apply a whitelist during advertisement on my peripheral device. Only one central should be whitelisted at a time. The whitelist is empty on initial...
Hi,
I'm using nRF52840 with ble_app_uart of ble peripheral example. And I'm using IDE is SES.
I want to put two deep learning model into my project , the two deep learning...
Hello,
I have the NCS v1.5.0 and would like to use AES (in different modes) in my non-secure application.
Looking at the crypto libraries available described here http...
Hi,
I am using two nrf52840 boards and a Light-Switch example included in the mesh SDK. One board is programmed with the proxy client , and the other with the proxy server...
Hello I am in the process of developing a central BLE and I would like to be able to transmit 240 byte frames with a device. The problem I have during my tests is that I see...
Hi,
I get " Could not fetch memory size of target devkit: Error: Error occured when get library info. Errorcode: CouldNotOpenDevice (0x4) Lowlevel error: LOW_VOLTAGE (fffffff4...
I want to use 9 axis motion sensor and I am planning to use INVENSENSE ICM-20948 for this. I know that all the sensors can interface with I2C protocol but the problem is I...
Hello,
DK: nrf52840
SDK: 15.0.0
i want to advertise accelerometer data with BLE/Beacon
so i tried to update the adv. packet for every 10 sec but its not advertising...
BLE DFU Mcu Mgr Error: NOT_SUPPORTED (8)
I am testing the DFU via BLE and get the message "NOT_SUPPORTED (8)" Does anyone have an idea what is not supported?
I logged the following error when I connect my PCA10040 nRF52 development board. The error is: Could not fetch memory size of target devkit: Error: Error occured when get...
Hi there,
First of all; I have experience in Keil but I am new to SEGGER and Zephyr.
Rebuilding our project in Segger using the new nRF Connect SDK I am stuck at adding...
Hi,
I'm running example mqttsn_sleepy_subscriber from nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8 on a nRF52840-DK with Paho MQTT-SN gateway on a Raspberry Pi 3 running...
I am using S132 v7.0.1 and while basic Softdevice functionality appears to work fine, I am getting an invalid address error when calling sd_ble_enable(). The pointer that...
