Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi
Is there an example for BLE "Just Works" using the NRF Connect SDK for the peripheral device?
I am using a peripheral device without display and would like to allow...
Hi,
In our application we use a motor. In the case that the watchdog would trigger while the motor is running, we need to stop the motor. For this we need to set the PWM...
Hi, all,
At first, I have to say I am a newbie in programming for BLE. ^^"
I trying to development a cycling power meter, so I want to modify this CSCS example to...
Hello, Recently I tested and flashed the Zephyr program to the nrf52840DK, it works fine. While I flashed as usual last time, I saw the LED5 flashing and then the PC didn...
I would like to perform a OTA DFU in a nRF52840 DK using nrfutil. For that, I'm using the example that is in SDK/examples/dfu/secure_bootloader/pca10056_s140_ble in the target...
Hi
I have follows the following steps.
1) I build 'hci_uart' sample for nRF5340DK successfully by following guide https://docs.zephyrproject.org/latest/samples/bluetooth...
Hi, I tried the fourth step of this guide https://openthread.io/codelabs/openthread-hardware#3 , but if I start the OpenThread daemon, I got this output that is not the same...
Hi There, I'm trying to read the NDEF records stored on my NRF52 DK but I'm having some issues when the the NDEF record payload is less than 4 chars. I just get random symbols...
Hello,
I've recently run into an issue with the Command Line Tools. I was using version 10.13.0 up until today, and everything was working fine. When I updated to 10.14...
Здравствуйте, я использую Honor 8x телефон. Я считаю, что это очень трудно использовать приложение на этом телефоне. Соединение происходит только один раз, и после одного...
as i said above,i got 1.5GHz radio signal,such as follow:
left is 1.5G,right is 2.4G
I want to know if the PA is configured correctly in my code.
here is my code:...
Hi,
What is the best starting point(Sample) for project with:
OS (like FreeRTOS)
BLE data advertisement.
I already install nRF connect SDK 1.7.0
Thanks
We have our one of Product Firmware of NRF52832 written in the Keilv5. As the Application use the Softdevice Functionality we need to load Softdevice code and Application...
Hi,
I'm using Windows 10, Python 3.10, Wireshark 3.4.9, pyserial 3.5.
Hex used : sniffer_nrf52dk_nrf52832_4.0.0.hex
I see this question has been asked before but the...
