I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Dear all,
Pushing the hardware to the limits, I came up with a question about the architecture of the microcontroller itself: Can two different instances of SPIM start...
Hello,
I am experiencing some strange behaviour through DFU process when build with GCC -O2 optimisation.
The upgrade process seems to complete successfully but after...
I got a device with a secure bootloader, but I lost the private key and the firmware got corrupted somehow. Is it possible to flash a new bootloader via BLE or is it bricked...
I am trying to understand the following, hopefully someone can explain:
AFAIK, BLE advertising is stopped as soon as the limit of the SD is reached, AKA the PERIPHERAL_LINK_COUNT...
Hello, I am I'm a novice at developing NRF 51822. My Development Environment sdk : 12.3 IDE: KEIL v5 SoftDevices : s130
It's being developed in this environment. Q1 .NRF...
Hi. I am struggling to build the DFU secure bootloader example for the n52 DK development kit. Using SEGGER embedded studio.
I get the following error;
cannot find .....
Hi Support Team,
We bought the nRF52 DK along with the PPK so we can measure current consumption of a DUT. It was working on the power profiler App in nRF Connect and we...
I am starting up with nRF52840, currently i have the dongle but expected to receive my DK in the next few days. This is my first BLE project, so i started reading a lot of...
We have a BLE peripheral implementation using the nRF52832 and both the S332 v2.0.0 and v7.0.1 softdevice. We are supplying the LF clock to the nRF52 from an STM32 MCO output...
Hi,
I would like to set up a couple of boards communicating over Bluetooth; I was hoping someone could provide some pointers.
I would like to connect the nRF9160DK to...
Hello, i'm trying to get usbd_msc example to work on custom, test pcb, with Microchip SST26VF064B flash chip (SDK version 16). As previously advised, i have redefined NRFX_QSPI_PIN_xxx...
Hi,
I wanted to setup a dynamic buffer but I don't have any leads on how to set it up.
Basically, i want to store a stream of data every time it is recorded and then send...
I know this has been asked a couple of times, but I haven't been able to find a straight forward answer.
I have a GPS module that spits out data via UART (no flow control...
Hello, Team.
I always thank to you.
I tried to find some information, but it is a little bit hard to find, so I upload this Q&A.
Now I'm interested in Mesh protocol...
