Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I'm trying to run Wi-Fi scanning or AP/STA mode examples on the NUCLEO-U575ZI-Q board with the nRF7002EK shield, but I keep getting an "RDSR2 register failed" error. I've...
Hi Team,
We are developing on a custom board with an nRF54L15 (Raytac Module with NRF54L15_xxAA_ENGB) and are unable to provision a pre-generated secp256r1 private key into...
I want to add WiFi functionality to an existing product without large altercations or chipset changes to avoid tedious rewrites/redesigns. The current codebase does not use...
Hi,
I would like to test a websocket connect over NB-IOT with the nRF9151DK. I started with the https_client example to do an https handshake with the server and then add...
Hi, I tried to start toolchain manager on my main computer and its not working anymore. I tried to delete all nrf related folders, deleted all apps including nrf connect deskop...
we want to use NPM2100 with 2.4V rechargeable battery, burst 2.4V to 3.3V @150mA.
there are a sepcial charger solution for the 2.4V rechargeable battery .
Could Nordic...
Dear DevZone,
While porting our project from NCS 2.9.1 to NCS 3.0.0, I ran into linker errors when building LVGL. The linker reports that it cannot find functions defined...
Dear, I'm developing on nordic 52840 with ncs2.6.1.
I found that the Current will reach to 600+uA in k_sleep state by enable SPI in device_tree and if i disable the spi...
Hi,
I send "chat private 0x0028 hi" over a serial terminal, and the MCU restart because of overflow, please see error log as below picture.
I tried to modify the "CONFIG_SHELL_STACK_SIZE...
My customer is now unable to disable secure erasure after using the APPROTECT function. Is this correct?
Please let me know if there is another way to check this.
”nrfjprog...
hi support team,
i am testing SLM demo.
i tried command as below:
[16:24:30.475] AT%XSYSTEMMODE=0,0,1,0
[16:24:30.496]
[16:24:30.496] OK
[16:24:30.496]
[16:24...
NCS currently has a nice feature where the firmware versions are printed in the boot banner:
Is there a config option to also enable printing the nRF91 modem firmware...
Hi team, We’re using the STM32H7 as the host MCU and the WMC02C Wi-Fi module (based on the nRF7002) connected via SPI on a custom board. I tried running the Wi-Fi scan example...
Hi
We are migrating from Segger Embedded Studio (SES) to VS Code for developing in the nordic connect SDK. We are using the RTT logger for debugging our device. In SES you...
We are currently using Zigbee Firmware built with nRF Connect SDK v2.7.0 on the nRF5340.
We plan to upgrade the nRF Connect SDK to v2.9.2 and use the Zigbee Firmware built...