I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
It's the first time i'm using the spi to connect various slaves, so is there any example how to communicate a raspberry with 2 or more nRF24L01 on the same bus?
Thanks in...
Today I have recieved the new nRF52 Development kit PCA10040. I did a update for the nRFgo Studio to version 1.21.2.3.
The softdevice s132_nrf52_2.0.0 will be flashed without...
OS: Windows 10
Target: nRF51-DK
Tried to connect with nrf51-dk with Keil MDK-Lite v5.18a.
The default Jlink version used along with this IDE was v4.98e
the 'download...
Hello all,
I'm looking at the example projects and ble_app_template in particular, and have noticed something that doesn't seem to make sense...
In main(), this project...
Hi, I am looking for a Bluetooth Low Energy Soc based solution like nRF51822, but I'd like to have an open source firmware solution...
Do you have that kind of solution...
Hi
I want to execute my app from the RAM to test if i'll get a considerable decrease in the current consumption.
I'm using : "s130_nrf51822_0.9.0-1.alpha" &"nrf51822QFAC...
Hi
I'm trying to change TX power and measure the current consumption while advertising, (DC/DC disabled) and i get an increase of 3.44mA from 0dbm to 4 dbm. Ok That's logic...
I follow the instruction and I am able to connect to Xively MQTT service. But I am confusing how to connect to AWS IoT MQTT.
AWS claim it support IPV6 as well.
Is there...
Hi all:
Here is my develop environment and it always show the message "one or more breakpoints could not be set and have been disabled".
Is any item I missed.
OS:Ｗｉｎ１０...
The ble_app_gls example does not provide any handling code for BLE_GAP_EVT_TIMEOUT, BLE_GATTS_EVT_WRITE, nor BLE_GATTS_EVT_HVC. I'm trying to understand whether the lack of...
I just ran a few experiments on calling sd_ble_gatts_hvx() multiple times based on SDK v10's ble_app_uart example. I have configure the app so that it for each external event...
Hi, I am using NRF51 Dongle to receive transmitted data from the NRF52 DK. currently , I want to send multi packets per connection interval. my question is that does the dongle...
