Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
HI,ALL!
I tried to add a RTC wakeup funtion to my ble device, so i add the code of the Nordic board example named "rtc_example" to my program.
But it turned out that my...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
What is the reason for the two 1u/10V 0201 size capacitors in the reference design? I understand you possess much more sophisticated equipment and expertise than I do, but...
Hi,Team,
I'm using the nrf54l15-dk to develop zms to save custom configurations without affecting the pairing information of ble.
So I have a few questions: 1.Is the storage_partition...
Hi,
I'm developing an embedded GUI application using LVGL on the nRF5340 application core with Zephyr RTOS.
The display I'm using is an ST7789 TFT panel (240×284 resolution...
I am trying to get the wifi stack to connect to a wifi AP using WAP2 Enterprise (initially just with identity and eap_password, later with full ca_certificate check and client...
I am trying to set up an try a solution for channel sounding. I have a custom pcb that has the me54bs01 from minewsemi with the nrf54l15 and i am trying to test the example...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hello Nordic Team,
I have a working project that uses BLE to communicate with a mobile app, and I am now looking to integrate Google Fast Pair as an additional feature....
i have the nrf5833 dk board, i just started programming from quick start and it worked two times and now it does not program at all, programming failed
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
Hi,
I’m working with an nRF52832 DK board that’s stuck in bootloader mode—LED 5 just keeps blinking. Here’s what we’ve tried so far:
Held the IF BOOT/RESET button...
Hi,
We need to write binary content from a binary file (.hex or .bin) to a specific area of the external flash (QSPI).
According to this topic: , this is similar to our...
hello Nordic
i am working with nre52840 and nrf52832, with ncs v2.8.0
i am using ble SMP service for transferring data with a central device and for DFU.
currently i...
Hello,
I am working with a custom board that has the nRF52840 (via the ISP1807-LR-RS module). This board has the SIT1552AI-JE-DCC-32.768E MEMS TCXO. This TCXO chip has a...
Dear Team,
I would like to know if it is possible to add custom attributes and commands to standard clusters, such as the Occupancy cluster. I have reviewed the "Adding...