I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi Nordic,
I had an initial project with a multilink central connecting to several peripherals through a NUS service, the system is working OK but then I added another connection...
I am using PCA10040 development board for flashing.Same it was working fine to flashing the Custom board.
Now suddenly not flashing to the custom board same board which...
I am planning to use CP2102 (USB to UART) and RF-BM-ND06 NRF52840 bluetooth module for sniffing BLE packets .
Or as an alternative for Nordic Bluetooth USB dongle.
But...
Hello, I'm pretty new to Nordic devices but I have already some experience with other ARM based devices though...
I'm playing with Timers bare metal instructions and figured...
Hi
I am currently trying to get the antenna switching working on the nRF52833 DK. I have an SPDT RF swtich which I want to use for switching between two antennas. I want...
Hi,
I've already asked this problem few days ago, but I couldn't figure out the clear answer.
The above figure shows the VDD values of BLE chip. The power supplied...
0> <debug> nrf_sdh_ble: BLE event: 0x26. 0> <error> app: Fatal error
I started with the nrf_tempelate project and used nrf_uart to add uart service. It works fine but after...
Hi,
I want to know that, can we use this nrf91 for transferring the real time data with tab or mobile phone beyond BLE range. I mean, do we analyse the real time data from...
Hi:
I have no dongle or any other Dev board such as PCA10031. Can I use nrf51822 and cp2102 as a usb dongle to work with MCU of PC? If the answer is yes, what should I do...
Hi All,
I am trying to decrypt some data coming in on my board with AES ECB mode. I know that there is no decryption function for ECB and you have to use the same sd_ecb_encrypt...
Hello, We are completing a project where is used the BLE device nrf52832. The product is composed by 2 devices: a peripheral and a central (both with nrf52832). The broadcaster...
Android update its repository android.support to androidX, so Nordic sample code of nRF_UARTv2.0 must do some editing to be a exectable code with the App,
Now we have met...
Hi,
I've developed nRF52832 chip for our company's application,
and I found some weird phenomenon
we using nRF52832 chip with Nordic softdeivce and SDK v12,
BLE...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
To reduce current I disabled NRF_LOG_ENABLED...
Hi,
Recently we have bought Thingy91 PCA20035 devices and tried to add to nrf cloud account but we end up with issues.
We followed the standard procedure to add the device...
