Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hello,
I recently tried some examples with nRF53 + nRF7002 (e.g. ble_coex example).
However, I am developing with nRF54 and I would like to understand if the combo nRF54...
Hi everyone,
I’m using a custom board (a tracker) that can travel at speeds up to 65 km/h and transmits data regularly every 200 ms. I expect, therefore, that the inactivity...
We're building a prototype board which uses the nRF52833 and want to tune the RF components. The radio_test sample in SDK 3.0.0 doesn't seem to support the nRF52833 SoC. Is...
Dear Nordic Support Team,
We are in the process of integrating the Nordic nRF Mesh SDK (version 3.3.4) into our custom Java-based application and require your guidance on...
Hi
I am working with a custom board with nrf52832 with only 32Mhz external crystal. My application is working in the nrf52832 development kit but when I use the custom board...
I'm testing BLE secure communication with the nRF52840DK device and I have encountered a problem with bonds. I use modified example from BLE fundamental course, in which I...
Hi Nordic Team,
I am using NCS v3.0.0 and working on a Matter-based application.
I have enabled the ActiveHardwareFaults attribute (0x0005) in the General Diagnostics...
Hi,
I am working on a project using the nRF52840 SoC with both Zigbee and BLE enabled, along with Mbed TLS and JSON libraries. Due to memory constraints, the firmware...
Hello,
I've an issue that I can't find clear instructions for the nRF5340 serial recovery for the network core.
Being able to update both cores from the bootloader level...
We are trying to add CarbonDioxideConcentration cluster in matter. we are able to add temperature and humidity clusters and values which are updated are getting read in chip...
It seems the "reset" button on my nrf52840dk doesn't do anything anymore. I believe this started happening after I enabled mcuboot in sysbuild. Is this expected?
NCS 2.9.1
NRF52840
Sysbuild but with only a single image (no bootloader)
I've been trying to figure out how to change the merged.hex output and how to perform additional...
Hello,
I attempted to follow the nrfutil offline install instructions. However, I keep receiving the following error when trying to install the device package on the remote...
When we were using nrfjprog to flash, we used "west flash --erase" because it was quicker to erase entire flash then sector by sector. However, when we upgraded to SDK 3.0...
I am using nRF54L15 with Zephyr to measure voltage with ADC. In the struct adc_sequence there is a calibrate bool, but I am not sure what it does. What is the reference that...
