I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
I am using VSCode with the nRF Connect extension (latest) and SDK 2.9.1.
I made my new app from the Bluetooth Peripheral sample.
When I try to debug I get the following...
I am using VSCode with nRF Connect extension with the 2.9.1 SDK.
I am trying to write my own device driver for the Zephyr OS and the TI CC1101 chip. Since the tutorial isn...
Hi,
nRF52832, SDK 17.1.0 with Softdevice S132.
Softdevice sleep does not work when advertising. Application flow is to advertise one packet, then go to sleep for X seconds...
Hello,
I use a PKK2 for power measurements on a nRF9160DK and Feather nRF9160 from circuit dojo. With the UDP example to test it out the sleep current so I can determine...
Hi Sigurd,
I'm finally using the mcuboot and mcumgr_cli I worked on in summer of 2023. I generated the mcumgr_cli for debian with go lang back then. I'm building my app...
Hi Nordic team,
We are currently investigating how to ensure that the fuel gauge continues learning and retaining the battery's charge/discharge profile over time.
In...
I am using Zephyr 2.9.0 with the sdk-nrf repo v2.9-branch checked out. The locator_tag sample builds without issue and flashes to the nRF54L15-PDK without issue. I have a...
I'm trying to use raw packet transmission (IN combination with wifi promiscous mode and raw sockets eventually) with my nRF WiFi device. I have both the sample raw_tx_packet...
Dear DevZone,
I would appreciate your assistance in understanding how to correctly configure Wi-Fi and BLE coexistence for the nRF5340DK and nRF7002EK with SDK version 2...
Hi! I'm testing the application with the custom Battery pofile I generated with nPM PowerUP app. During testing I found the issue with the SOC value calcultation depending...
Hi Nordic Team,
I am planning to develop a SmokeCo device using the nRF54L15. I tested the example code of Smoke-Co from nrf-sdk with nRF54L15-DK and that working correctly...
Is there a trick to getting nrf_dm to compile on the nrf54l15?
I've installed v2.9.1
Command I normally use (nrf52840):
west build -b nrf52840dk_nrf52840 -d build_nrf52840dk_nrf52840...
Hello,
I am using the following device and development kit:
Device: NORA-B106-00B (nRF5340)
nRF Connect SDK: 2.0.2
Currently, I am trying to use GPIOTE PORT...
I've been trying to run the example Mesh/Chat on NRF7002DK, and the terminal print <err> bt_mesh_pb_adv: Failed enabling advertiser and <err> bt_mesh_pb_gatt: Failed enabling...
