Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
Hi Nordic,
I am currently writing about the process of performing channel sounding sequentially on three connected devices. However, after the first channel sounding is...
Hi Support Team
We try to integrate the flowing links' sample code of Mesh Sensor, Mesh LPN and Mesh DFU to one project for nRF52832, but we found that the memory usage...
hi support team,
i have customer is developping mesh.
customer is trying to sniffer the message when i pressed the buttoon on demo mesh_light.
i have two questions on...
hi,i am using zephyr`s sample of gpiote,it works well,but i don`t know how to optimize the power consume of gpiote:
1,how to setup PORT EVENT?
2,Sometimes i want to reduce...
SOC: nrf52840
SDK: v2.9.0
Device is a central, it connected to 16 peripherals, these peripherals will power on 90 seconds and then power off 10 seconds(one cycle). ...
Hello,
In my project I use a nrf52840 which have the access port protection. I am in the development phase and I would like to disable this protection during this phase...
I'm developing with an nRF52832, NCS v2.6.1 and Zephyr 3.5.99
I've been forcing my MCU into System Off when I don't need it to do anything, then triggering it out of that...
Hi,
I am working on zigbee demo "light_switch" with NCS2.8 Add-on SDK.I enabled MCUboot according to the steps in the course " Lesson 9 – Bootloaders and DFU/FOTA "
1...
Hi,
SDK: 3.0., nRF54L15
The application is Matter + BLE dynamic multi-protocol + battery powered sleepy end device. Current Application(Matter/Thread + BLE + Firmware...
Hello, I am trying to develop a bluetooth mesh network with two provisioners, one being an external provisioner (mobile phone) and another being node in the network (nrf5340...
Hello, I am trying to use the subghz template in ncs 2.5.2 but I am running into an issue when enabling NanoPB. When enabling NanoPB with CONFIG_NANOPB=y the application faults...
Hi there.
I am trying to implement a 16-bit, 32kHz, 2 channel i2s interface which is being fed by a FIFO (the final source of this FIFO will be a DAB/FM radio module but...
Hi,
when i try making a new connection with a new device using my for loop (reconnecting using the adresses that i stored in an array), i sometimes can get a warning which...
Hi,
I am trying to use nfc_t4t_lib and I have some issues because processing incoming data takes some time (around 100 ms) and therefore sending the response occurs late...
Hi all,
I'm trying to integrate joiner into my project, here's my goal:
We will start a device as our commissioner, and while it is active, we will start the other devices...
