Hi,
I would like an nRFX example on how to set up DPPI using single in (1 Event) and multiple out (2 Tasks). I have previously done this using the fork functionality in...
Hey all,
Every time I flash, I get the following error message:
Error: One or more batch tasks failed: - [Probe] Device error: Memory access error at 0x00000000. Probably...
Hello everyone,
I would like to learn how to create unit tests using the ZTest framework for a Nordic sample project, in order to better understand how it works.
I am...
The VSCode nRF Kconfig extension has very high cpu usage (2 cores at 100%)
When disabling the extension, the cpu usage drops back to normal.
I see the following in the...
Hello,
Yesterday, I received a new Power Profiler Kit 2 device directly out of the box, and unfortunately, it is not detected by any PC.
Symptoms: - The green LED blinks...
We are using the nRF5340 and our use case makes full use of all 4 shared peripherals for SPI and TWI as well as SPIM4. We want to add UART over USB and I was able to port...
Hello together, Which configurations or setup on the side of the Nordic nrf9161 DK has to be done to use the DEBUG IN connector for SWD? The board is powered by the 5VIN pin...
Hi,
We have some GPIO pins where we want to change their configuration during runtime. We want to switch them between input pull down and output. Is this possible?
When...
Hello, I want to disable parts of my RAM to save power. I implemented this in my project based on the System_Off ram retention example. I'm now not sure if RAM retention is...
I noticed that the product information of the nRF54L15 series kit supports 4Mbps, but I'm unsure how to verify it. Are there any relevant examples available? I have currently...
Dear Nordic Support Team,
I am experiencing difficulties flashing firmware to my nRF52832 development board using VSCode with west flash , followed by J-Link...
Hi, We are using nrf Connect SDK 2.4.0 and have been looking through the NIST vulnerabilities databases. One of the vulnerabilities reported with the nrf5340 is a denial of...
Hi,
I am using nrf52832dk board for test nus service with ncs2.9.0, but I am facing some problem with MTU setting.
I found a configuration item "
CONFIG_BT_L2CAP_TX_MTU...
My application is based on the ncs nrf5340_audio application, but my application and hardware target are both out-of-tree and I am using ncs v2.9.0.
I am able to connect...
Hello,
I have a firmware that sends every 15 min a packet to nRFCloud using nrf_cloud_coap_json_message_send().
The code is working great most of the time : hundreds of...
Hi.
We have a device connected to Azure IoT Hub with telemetry interval set to 10 min and on interupt. Tried changing interval to every hour, but then it looses connection...
I've tried the following with the Quick Start app v1.2.0, v1.1.0 and v1.0.1. The log below is from v1.1.0, if I recall correctly. All logs are about same. Programmed the Asset...
Hello,
I'm trying to enable RTC2 for nrf52840 DK to use as a date time clock and set/get over SMP protocol. RTC0 is used for MPSL, RTC1 is used by the system.
I configured...
Hello Team, We are currently using the nRF52833-QDAA-R SoC for our R&D activities and have assembled the board based on Configuration 6 . However, we encountered an issue...
I followed the steps here docs.nordicsemi.com/.../building.html: PS C:\ncs\v2.9.1\nrf\applications\nrf5340_audio\tools\buildprog> python buildprog.py -c app -b debug -d gateway...
Hi everyone,
I'm developing a BLE application where I measure throughput between an nRF5340DK acting as peripheral and an nRF52 Dongle as the central (using a Python script...
Hello,
I'm developing for nRF54L15 the application with the NSIB + MCUBoot. I have a problem with fprotect in mcuboot returning EINVAL error. That happens due to limitation...
