after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I have a Custom Board made by using nrf51822 soc but pc is unable to detect the board by using Jlink debugger.
Stlink was able to detect only when frequency selected as 20khz...
Hello dear Nordic Team,
I got a question regarding the device filtering options. I am interested in putting 10 chips next to each other. But every chip shall have only...
As I came to understand, all the services & characteristics are registered in a "GATT table" of some sort, so my question:
What are the functions used to create and...
I want to update the nordic device from another MCU with HCI DFU. I cannot figure out how to write the packet header.
In the Nordic documentation, it is writen to read the...
I want to add micro-ecc library for compiling bootloader secure code.
I tried as mentioned on infocenter.nordicsemi.com/index.jsp .
I am getting error as attached. I am...
Hi,
we use the GPIOTE to get informed if the value of a GPIO pin gets from hi to low.
If this happens, the GPIOTE event handler will be called.
What will happen,...
Hi, I'm using a nRF52 dk board as a switch to control a circuit. The problem is I not sure which gpio can be used to act as a switch to control the circuit. Thanks.
I need to append another binary-file (image.bin) to the generated bin-file from my own nRF makefile Project in Eclipse with Cross ARM GCC. My research showed me several possibilities...
Hello,
I have a standalone application which incorporates 3 public BLE services and 2 services with custom UUIDs.
Today I tried to extend the buttonless DFU example with...
Hello,
I have installed Ozone (V2.22g) on Kubuntu (16.10 64bit) and attached a nRF51DK via USB. I can successfully run a test program using nrfjprog with the following...
Hi,
I'm not sure if I understand the new reference layout correctly. There are new NP0 12pF capacitors on pin 25 and pin 26 to suppress the spurious emission, but are they...
I'm trying to flash the nrf52832 with a SWD debugger called Atmel Ice . As a reference, I have the Laird BL652 dev board .
I was planning on flasihg the nrf52832 by using...
Hey,
Could you please explain, in your reference designs, why you suggest to use solder mask clearances that cannot be produced?
0.045mm is not possible produce and...
