Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Dear all,
i building the example light_switch_server_nrf52832_xxAA_S132_7.2.0 from solution l ight_switch_server_nrf52832_xxAA_S132_7.2.0 in configuration Debug (SDK nRF5...
I am trying to do the dfu update in my custom flutter application like it does in the nrf connect application. My device is correctly being put in bootloader mode and the...
Good day,
I am trying to program the nRF Sniiffer firmware to my nRF52840 dongle using the "nrfutil device program" command.
According to the User Guide v3.2 for the nRF...
Hello,
My new dev kit is not being detected by Windows Device Manager right out of the box. I've tried multiple USB cables and I've confirmed VBUS=5V is present on the input...
Hi,
Programmer can't read chip information after i download firmware with VSCode.
Before download, Programmer can read chip information.
Tool : Visual...
Hi all,
I applied QSPI driver on NCS 2.4.0 with QSPI LCD panel and I encountered the problem.
The red area is the data I sent, but the blue area is not what I sent....
Hi everyone,
we are trying to use the TWI interface of the nRF52832 to communicate with a TI BQ28Z610 fuel gauge, using the TWI driver of the nRF5_SDK_13.0.
For the last...
This sounds like a stupid question... but I would like to clarify if this pin is an input or output. I think it's power in but want to make 100% sure as I'm spinning a PCB...
Hi , am working on nrf52840 .with nrf desktop v2.9.1 . I am working on display ST7789V with the nrf52840 using Zephyr. I have integrated overlay file . while working on it...
Hi team, According to this statement, it indicates that access port protection can be deactivated by modifying the TAMPC.PROTECT registers, which can be achieved by executing...
I'm currently working on configuring the nPM1300 used in our custom board. In the product spec v1.2, it supports 2 USB compliant current limits, IBUS at 100mA and IBUS at...
I am trying to add Coded Phy to my Zephyr BLE Mesh project. I know this is not officially supported, however is possible. Running the stock BLE Mesh Zephyr sample, I keep...
Hi, We are currently working on a new product based on NRF54L15. Goal : We are trying to set up the "Bluetooth LE UART service" example in order to transmit and receive data...
Hi,
I'm doing a test with a matter test harness. An error occurs in test case _TC-CNET-4.16, _TC-CADMIN-1.22 and _TC-DGGEN-2.3.
1. _TC-CNET-4.16: Step 2: should receive...
Hi Nordic team.
We are developing the LE audio product, and have questions here.
We have design a headset board using the RT5616 as codec.
The modifications here are...
