Nordic Support,
My product uses the nRF52840 chip and nRF52 SDK 17.1. I have a feature request to support hosting multiple peripheral connections, each with a unique advertising...
I am working with NRF52840 with SoftDevice S140 and SDK v17.1.0.
The boot loader address for this chip is 0xF8000. I can set up one of the 'fstorage' module with the address...
Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
I am using OpenThread network and working on CoAP Client and Server examples (Customized). Everything working fine when devices are on main power.
My client devices are...
I am running VSCode with the latest nRF extension. I am on v2.9.1 of the SDK
I created a new app and copied the bluetooth_st_ble_sensor sample project.
I would like to...
Hi,
I used the nRF52840 board with SDK v2.8.0 .
When we tried to build this example code, we encountered the following error: v2.8.0/zephyr/include/zephyr/device.h:92...
Hi!
S132, SDK17.1, nRF52832
Very strange behavior, I connected my central to the bonded peripherial success and got an BLE_GAP_EVT_CONNECTED event, but when I disconnected...
Hello,
I'm working on a custom board with a nrf54l15 chip.
I would like to add an interruption on the GPIO P2.10. But I get an error -ENOTSUP with gpio_pin_interrupt_configure_dt...
Hi Support Team,
I tried several ways to set the image version but failed. My SDK is ncs V2.5.2. 1. set(CONFIG_MCUBOOT_IMAGE_VERSION "1.0.0") in CMakeLists.txt: did not...
Recently I've had an issue with 3 of our nRF9160 based products during production (several hundred of the same hardware/firmware/SIMs work fine). The issue is that while the...
Hello Nordic support,
My application is a Zigbee coordinator application on nrf52840 based on nRF5 SDK for Thread and Zigbee v4.2.0. I was able to pair a Zigbee end device...
I am using the Zephyr SPI driver to control a WS2812 LED strip through the SPI interface. Since only the MOSI line is required for communication, I want to configure the SPI...
I am developing a device that uses ESB.
Uses modules that are Telec and FCC certified with BLE profiles. (module : MDBT50Q-512K)
I have a few questions.
Q1. The TX power...
I have two boards:
nRF52840 DK (which has a faulty buck converter, so I am powering it via USB).
Fanstel BT840F board , which provides power to the Debug In connector...
I used nrf5340 on my board and did some changes based on audio demo.
Unfortunate,I heard a noise after set configure like bis gateway, audio input from usb ,48k 16bit 2channel...
Hi,
I have a problem with unmodified BLE Shell and changing security level to 2(aka just works).
1. I'm connecting from BLE Shell to the device that requires level 2 2...
I am attaching an adapter board to the nRF52840DK to debug a custom board.
However, if there is any contact failure on the adapter board, the nRF52 on the DK will be the...
