Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
I use NRF54L15 DK to develop channel sounding feature on zephyr SDK or nRF connect SDK.
How to configure CSTONES related registers to transmit and receive CS Tone packets...
Hello,
I’m working with a custom board using the nRF54L15 and the latest Nordic SDK, and I’m facing an issue while trying to communicate with an nPM1300 over I2C.
Here...
Hi all,
I'm working on a project with an nRF52840 using the nRF Connect SDK (version X.Y.Z) and Zephyr RTOS. My goal is to achieve maximum possible range for non-connectable...
nrf modem: 1.3.4
sdk: 2.3.0
Custom board.
We have an asset tracker that caches events when out of connectivity zone. We can accumulate 10-100 messages depending upon...
Hello!
I have designed a custom board with the nRF5340 , powered at 1.8V. I am able to program the chip successfully, but after the firmware is downloaded (Zephyr RTOS,...
In my application we have an nRF514L configured as an SPI target. Page 830 of the nRF54L datasheet (version 0.8, dated December 2024) documents that the SPIS peripheral requires...
I'm trying to convert some code from ESP32 to nRF, and I'm having problems with the microphone input. Mind you, I'm a beginner with nRF, so I'm sure I'm missing something...
Hi,
We want to enable zephyr shell over RTT on our custom board based on nrf52840. I tried the 'shell_module' sample with prj_minimal_rtt.conf and it works fine on nrf52840...
Hi there,
I built a battery powered custom PCBA with the NRF54L15 and the nPM1300. All the configuration and register work via I2C seems to be working properly (reading...
Hi,
We’re working on a device using the nRF52832 and have DFU over BLE working correctly using internal flash. Updates work both via our custom app and the nRF Connect app...
Hi. I have a working IAR project based on the nrf52 SDK \nordic\examples\ble_peripheral\ble_app_uart. i am attempting to port the project to ARMGCC using VSCode. I am at a...
Hello. I try to create a remote control for GoPro using nrf52 ble.
Using sdk 17.1 examples I can connect to GoPro and try to get a list of UUIDs. But I only get one UUID...
Hello
I'm using the settings partition to store user configuration data. I know that the BLE stack also uses it — particularly for storing bonding information — but I don...
Hi,
I am working on a project with nrf52832 and LIS3DH for a beacon.
I have added the low power feature into my application to go to standby mode in case of inactivity...
Hello Everyone,
I am using a nrf54l15 for my current project and ran into some discrepancies within the documentation provided for the processor.
Even the AI chat bot...
