Hello,
I'm here again because this time I need to autoconfigure (configuring from inside program, no use of any nrf app) heartbeat destination node and source node.
For...
We have developed an application which uses the nRF9160 together with the same GPS and Ethertronics/Kyocera/AVX antennas as that of the nRF9160-DK . For the LTE antenna, we...
We're trying to measure supply current used by the NRF9151 DK but have discovered that the current measurment connector (P22) only includes current supplied to VDD, and that...
Hi,
I am using nRF54L15-DK for Zigbee light_stwitch startup testing. After successfully connecting the development board to the Hub for the first time, I evaluated the time...
Hi
I have a code previously can be built in NCS 2.91:
However, when I use the new NCS 3.01, it can not be built, the error is:
Could you please help me figure out...
Hi,
I am trying to integrate the nRF5340 Audio application (CIS Unicast Server role with bidirectional streaming enabled) from NCS 2.9.0 into on my custom nRF5340 based...
nRF52840 NCS 3.0.1 RCP
I just installed the NCS 3.0.1 SDK. I am trying to set up a border router on a Raspberry Pi 4.
I followed these instructions on the Raspberry Pi...
I have a class that wraps the Zephyr implementation of a mutex. For some reason, when the code runs, I get this error: ASSERTION FAIL [mutex->lock_count > 0U] @ WEST_TOPDIR...
I am using LVGL for simple Eink display UI, and trying to implement a simple if condition to check if the passed string argument is null as below:
If I only have btn1...
There are two USB ports. IMCU and nrf5340. I had a lot of trouble with bad cables but i found one that works and I find that I have a jlink drive that pops up so I know there...
Hi,
I am working on RF testing on the custom board.
I have configured the nrf UART TX in p1.04 and UART RX pin in p0.13.
UART TX pin is working fine, but the UART Rx...
Hello - Above is an error message I am encountering when attempting to use the NFC record_text sample code for a nRF54L15DK in TF-M as the Secure Environment.
The samples...
Hello.
This ticket was derived from another ticket .
I have a few questions about hardware-based downgrade protection.
About the Downgrade Protection of the Network...
Hello!
I’ve been learning about Bluetooth Mesh recently, and I’ve been testing the sample at nrf\samples\bluetooth\mesh\chat , but there are still some parts I don’t quite...
I'm using these devices for a personal project, I'm an experienced software engineer but relatively new to MCUs, I know this is a legacy product from Nordic's standpoint but...
I'm an experienced HW engineer with minimal SW experience. I just went through your SDK fundaments with an nRF52840DK to get acclimated to your SDK and brush up on some C...
This stopped working for me... Error is the following
Command failed: git ls-remote --tags --heads github.com/.../sdk-nrf
fatal: unable to access ' github.com/.../'...
I am a beginner to BLE Communication ,
Currently I am working on a project where I need to connect a peripheral device ( Central (nRF52840) ---> Peripheral (BLE device)...
Hi all,
I may have encountered an issue with nrf9151DK board.
When I only set LED1 with dk_set_leds (DK_LED1_MSK) the LED1 and LED2 are both lit.
Setting other leds...
im looking for a developer that can help me work with the NTN functionality of the 3GPP release 17 of the NRF9151-DK so if you are interested please write to me at eric@zerocool...
Hi everyone.
I am using Visual Studio Code. When i try to compile a simple blink_pwm project, I could not. I am sending output in terminal. What is the main problem and...
Hello!
I am working to design and build a custom PCB using the nRF7002 chip and came across this callout on the schematic diagram and wanted some clarification about it...