Hello,
I've been asked to create a new ticket for this. It follows on from
@ Erlend Isachsen asked:
So before marking this problem as resolved, it would be nice to be...
I am developing on the nrf9151 with SDK v3.4.0.
The device I am developing will be moving trough all of europe . My goal is to speed up the `AT+CFUN=1` conenction part of...
HI
I am currently carrying out secondary development for PAWR based on NCS 3.2.1. I understand that its communication adopts frequency hopping. I would like to ask whether...
NCS-3.4.0, on nRF5340, custom board losely based on PAN1783. No RTT backend, BLE stack works properly:
RTT enabled, BLE stack reads some garbage:
Printing is done...
Hello, our design does not use the USB block of the 52833. In the electrical schematic we have connected VBUS (AD2) to GND and we leave D-(AD4) and D+(AD6) open. Due to a...
SDK: nRF Connect SDK v3.4.0 (TF-M v2.3.0) Board: nRF9151 (seen on both nrf9151dk and a custom nRF9151 board) Config: CONFIG_TFM_PROFILE_TYPE_MINIMAL=y, MCUboot with CONFIG_USE_SEGGER_RTT...
I am looking to evaluate Amazon sidewalk on the nrf54L15 dev kit and have also bought both of the Semtech evaluation boards LR1110MB1LCKS and SX1262MB2CAS. The nrf54L15 is...
Dear all:
I have prepare env for border router successfully following this link( developer.nordicsemi.com/.../tools.html , Raspberry Pi4 and nRF52840( RCP: radio coprocessor...
I have a customer that wants to provide me with .a file for some confidential algorithm they want to run. I am tasked with implementing this into my firmware.
Using the...
I can't seem to get the FIFO to work and I think it is because I'm not dereferencing the consumer thread properly. I have reviewed the nRF Connect SDK Intermediate, data passing...
Hi,all
I need to connect BLE via NFC,but I do not know which example should i use to start。and i am a new field of NFC ,is there some document about NFC?thank you a lot...
https://devzone.nordicsemi.com/f/nordic-q-a/44658/communication-probl
I want to change the code provided in this link to enter the password from the peripheral
Hello,
I am using nRF Connect 2.5.2 with a Xiao Seeed BLE Sense nRF52840 and Jlink EDU mini
I am trying to flash the peripheral_hids_keyboard sample with Ozone, and I...
Hi everyone,
I'm trying to measure battery level using nRF52833. Reading previous posts, there are two popular ways to measure battery level with SAADC module 1) battery...
Dear All,
I need your help to clarify some LE Audio protocol related concepts.
For the BIS use cases. When the PC pause the playback, after that, are there any ISO packets...
The MCUboot, Slot0, and Slot1 flash partitions are defined in the board file. E.g., nrf52840dk_nrf52840.dts has boot_partition at 0 with length 0xC000, slot0_partition at...
OS: Windows 10
NCS: 2.4.2 We are evaluating adding the APDS9960 to our existing nRF52833 based application, but can not get the APDS9960 functioning. We are interfacing...
Hi,
in the PCB circuit I marked in the pictures, it seems that vias have been added to the marked areas on the pads of the nRF52840. However, PCB manufacturers say that...
Hi, I am relatively new to the Nordic platform and Zephyr RTOS. I am using nRF Connect SDK version 2.6.0 (the VS Code extension on Windows 11) with the nRF52840DK. I was wondering...
Hi,
I am designing a two Layer PCB with nRF52840 with PMIC, RTC, Flash. Can anyone from Nordic Review it? especially the RF antenna, I have used the Reference design from...
To verify my Custom antenna design on a PCB . AND VERIFY THE PCB.
https://cart.jlcpcb.com/quote/gerberviewThree/?qs=582f0d800a0c49398584815906f24877_1_0_1_0_0.html&_gl=1...
Hi
We are developing Zephyr projects which are compiling and working fine with Visual Studio Code running on a Windows PC.
Now we want to build the projects on a build...
