I2C on i2c2 (the Arduino header, arduino_i2c , P0.30 SDA / P0.31 SCL) is completely non-functional on two separate, brand-new nRF9151 DK (PCA10171) units. A raw bus scan finds...
We have switched over to the new device tree based partition scheme, and developed custom board files with not-secure variant and mcuboot for ota. OTA was tested using BLE...
We have a product in the field using the NRF9160 and AWS IOT MQTT from NRF Connect SDK 3.1.1. It is always connected when awake (power cycle controlled by an external micro...
Dear support team, on our board we have an nRF54H20 which we connect to an external can transceiver using `can120` node. When the board goes to standby state we want to disable...
Hello,
I am trying to flash and debug a custom board using the Raytac MDBT42Q-512KV2 that uses the nRF52832 module mounted. I tried this using the jlink plus and the nRF52...
Hello,
We are using A-GPS in our application to get faster TTFF and will be reading location coordinates after every 5 mins of duration. The application flow looks like...
Hello, On a custom board, using the NRF52832, we want to know the value of a potentiometer. This value is send via a signal on the AIN5 pin of the NRF52.
So, I tried to...
I am using nrf52833 to make a Thread end device as SED and RCP. All firmware versions use NCS V1.8.0.
The compilation options for OTBR is: CMAKE_OPTIONS += \ -DOT_THREAD_VERSION...
Hi,
I use the BLE_APP_UART example for reference and in the code there is the ble_evt_handler with the following states:
case BLE_GAP_EVT_CONNECTED: case BLE_GAP_EVT_DISCONNECTED...
Hi,
I faced the exact problem nda , here . I take step just like nda did before. I unchecked "Enable debug options" as Marte Myrvold told, but still the same problem.
...
Hi,
I'd like to test the Adafruit NFC reader example provided in nRF5_SDK_15.3.0_59ac345. I'm using a nRF52832DK and I2C communication, as shown in the picture:
The...
Dear Nordic Support Team,
I am developing an application for the nrf9160 DK version 1.0.x (nrf connect sdk 1.8.0 and modem firmware 1.3.1). The application depends on other...
I have a project that is reading an external flash chip via qspi. Everything is working well, and I haven't defined the sfdp-bdp field in the overlay file that defines the...
Hi All,
I am trying to test the SPI flash example provided in the zephyr samples folder. Below is my qspi dts configuration.
SDK used: NCS v1.7.1
Same code works in...
Hi Team,
We build the bare application with nRF52840 Soc with the SDK Version 16 with out any RTOS Layer. We are planning to port our code base to Zepher RTOS layer.
We...
Hello everyone!
I am trying to get my Thingy 91 to work, but I am stuck.
When I flash it with pre-compiled .hex at_client sample ( "thingy91_at_client_2021-12-15_cfedfdfa...
Hi, I'm working on nRF9160 modem firmware update.
I have used nRF9160: Full modem firmware update using SMP Server demo and compiled it for nRF9160dk board. While compilation...
We are building an application using McuBoot and Zephyr, providing the provisioning via haptools and packing the image all together. What currently bothers me is that I cannot...
Hello,
I am attempting to use SPI and I just wanted to trial the transceiver option however I am not having any luck. I have tried it three ways but as you’ll see I’ve made...
Hi
few questions on DPPI:
where is it possible to find examples in nRF Connect SDK to learn to use DPPI on nRF91?
Is there corresponding documentation?
For which...
