In nRF cloud, in the device list ( https://app.nrfcloud.com/#/devices ) it is difficult to manage larger number of devices because of lack of search and limited sorting. ...
Hi,
We are currently migrating our project from nRF52840 to nRF54L10 using the nRF Connect SDK , and we have a few questions regarding MCUboot DFU using external flash ...
Are there any specific points using the external flash of a Thingy:91X?
I tried to adapt the "nrf/samples/cellular/modem_trace_flash" by adding an overlay copied and modified...
Hello,
I am using the same hardware, and firmware on 4 custom boards of the same device. I observed that I am getting different current consumptions in each devices.
I...
I’m working with a device that communicates over single-wire UART (half-duplex), where TX and RX share the same line (because the peer device is designed that way). Now I...
Hello,
I recently got a BL653 Click Board and am trying to program it. As I do not have a supported MCU for the NECTO Studio IDE (the ClickBoard's manufacturer IDE), I...
Hi,
I'm looking to use the nrf connect sdk for development that is compatible with the latest zephyr lts. I believe it will be ncs 2.9.2 compatible with zephyr 3.7.99 (3...
Hi,
I have seen this post , but it is quite old, so I would like to know what is the current solution to
update advertising packets while advertising, without stop and...
Hi there. I am freshman with the NRF MESH. I am working on project which I need to use the static provisioner node. The problem I am facing is how to configure multiple group...
Hi everyone.
I want to stream 12kB of ADC data from the thingy 52 via BLE. At the moment this takes around 4 seconds to do which is to slow so i would like to increase...
hi ,when develop the usb + gzll+ble hid funcation, i find that it will occur a erro when stop the ble stack in the project that have usb funcation,so i try in the project...
Hi,
I'm trying to debug CLI example contained into nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b by flashing it on my nRF52840 DK (PCA10056).
First of all I'm using...
Hello DevZone,
Currently I'm working to get the NFC examples up and running.
I'm using the PCA10040 in combination with SDK15.0.0 and SD 132
A colleague of mine mentioned...
Hi everyone,
I suppose this is a very simple question... I want to create multiple timers using the Timer Library .
Each time I want to create a new timer based on RTC1...
Hello,
I'm flashing custom code onto a nRF52840 based PCB.
I'm using SDK v15.0, SES 4.52.
On the debug window I get the following message as soon as I run the code...
Hi,
I am using nRF52840, S140 V7.0.1.
I am using Secure Serial Bootloader and able to do DFU of Application.
DFU of application
Using below command able to generate...
Hi,
I have a custom board with nrf52833 I would like to flash with custom firmware. I would like to flash this board by "P19 debug out connector" from DK.
How can I...
I am trying to port a tested program from NRF52 DK to NRF Thingy. To do the same I had changed the board to PCA20020. After I do that, I program using the NRF52 debug out...
Hi,
If the app keeps sending data at a certain rate, the numbers will skip and the software will stop.
I tried to see how much data I could communicate and at what speed...
In my situation, I want to use ble to designed a piconet which has 1 master and up to 4 slave .( upload(Slave->Master) rate is 2.2KB/s,download(Master->Slave) rate is 500...
Hi
A few questions regarding the "saadc_pca10040" example:
If I read one analog pin then what is the meaning of this matrix of values :
"static nrf_saadc_value_t...
