Before buying two nRF54LM20-DKs, I need to know which way is supported. Our own protocol uses RADIO directly: in each 20 ms period a SYNC goes out at 30 µs, started by a TIMER...
The Thingy:91 X board files allocate only 32 kB to the TF-M secure partition (slot0_s_partition). This is too small to support CONFIG_TFM_PROFILE_TYPE_MEDIUM, which is required...
Hi,
I am designing a PCB using the nRF54L15 (QFN, 3.3 V system) that must meet IEC 61000-4-2 Level 3 (±4 kV contact / ±8 kV air discharge). The on-chip ESD rating is only...
I am developing a proprietary 2.4 GHz distance measurement with two-way phase-based ranging and RTT on the nRF54L15.
I intend to control the RADIO peripheral directly, without...
I am seeing a reproducible interaction between asynchronous UART support and the TWIS peripheral on an nRF52840 running NCS v3.4.0.
The application uses nrfx TWIS to implement...
I'm not sure if I can share the files here, but you can email me at kc6ete at gmail if you want a copy It's a four color print designed for the Snapmaker U1 though it can...
Hello,
My questions is regarding to the modem firmware.
I am planning to ship an IoT product and am questioning wether I should include an external memory for modem FOTA...
Hello, I'm stuck at the build step from teh IoT fundamentals course as when I try to build I get the next error:
It seems that the build needs two (samples/cellular/nrf91_crypto_partitions...
I happened to write some debug log code that broke my Bluetooth. I don't think it should be doing that. When I burrow into the logging, I don't see why this difference is...
We have switched over to the new device tree based partition scheme, and developed custom board files with not-secure variant and mcuboot for ota. OTA was tested using BLE...
Hi, I have a question with regard to the nPM1100 PMIC and entering ship mode (not exiting it).
If I am interpreting the datasheet correctly, the SHPHLD pin must be held...
Hi Nordic,
We are building a custom board using the nRF9151 LACA.
We see a back-powering issue between the GNSS antenna bias rail and VDD_GPIO.
Setup:
VDD_GPIO...
Hi:
I use ncs3.3.0 and nrf54l15dk.
PC BLE pairing nrf54l15dk failed log:
prj.conf
But with BT configuration, turning off ESB related content, it can be paired...
I have a nRF52832 custom board derived from the 52832DK board. All is working perfectly with the exception of the ADC converter. I am only using AIN0 which is on pin 0.02...
Hello,
I am working on a device based on nRF9160, SDK 2.8.0 and modem 1.3.7.
The devices uses nRFCloud CoAP to send messages. For the most part, it's working great....
Hello, I am currently experiencing an issue with the 802154_phy_test example on the nRF54L15-DK board, and I would appreciate your technical support.
[ Environment ]
...
In theory all driver calls are suspect, but for example I see crashes in nrf_802154_buffer_free_raw, at this assert:
This is easily reproducible by running 802154_phy_test...
Hi, I have an Ubuntu 22.04 LTS virtual machine where I installed the version v3.4.0 of all the needed tools and libraries as explained in nrfconnectdocs.nordicsemi.com/.....
Hi,
I am experiencing an issue where SPI read operations fail after upgrading from NCS 3.2.4 to NCS 3.4.0.
Hardware:
Custom board based on nRF52840
ADS1294...
