Hi, I'm pretty new to microcontroller programming so please correct my wrongs.
I'm using the Libuarte driver library to have the pca10040 talk to my server via serial connection...
Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
I'm trying to add a second element to (light_switch\server) (SDK_for_Mesh_v5.0.0). I've already have a look at this post , it gives an idea but I found that it's not applicable...
Hi,
Again the topic which has already been discussed several times in this forum. I just want to share my experience and perhaps help other users having difficulties.
...
Hi Nordic team,
The LTE link monitor app is not showing up in my NRF connect for desktop v3.6.
What would I need to do in order to add it?
Is there a http link you...
Hello,
Using scan sample I am trying to read drone Remote-ID. When broadcasting Remote ID via Wi-fi Beacon no problems occur, but once selecting only Wi-Fi NAN as delivery...
Hey! I'm working on a LE Audio project utilizing the nRF5340, where I need to stream audio both from and to the nRF and I have encountered the error "sw_codec_lc3: LC3 enc_bitrate...
Hello,
I can see there are some ADC examples on Github https://github.com/NordicPlayground/nRF52-ADC-examples But those examples are nRF SDK5. Are there any ADC examples...
Hello everyone,
I have a problem using pstorage_update. Normally it does as it should, but once i call ble_stack_init(); on my code, pstorage_update doesn't work anymore...
Hey,
I am trying to use the example for Sync_Advertising_conn to get a connection between 2 nrf5340 devices. but I get this message
the problem is in the config
CONFIG_BT_PER_ADV_SYNC_RSP...
Hello,
I am using the nRF52811 on a keyfob that transmits short packets when a button is pressed. The button directly connects power to the MCU, and the firmware immediately...
Hi,
I've just received my new nRF9161 Development Kit, but when going through the Quick Start, it fails to program.
Log:
2024-06-19T20:51:59.582Z INFO Initialising...
I am trying to interface nrf52833 devkit with BG95 devkit using PPP connection. For this I am using gsm_modem sample code. But when I am getting error while build configuration...
Hi,
We are wondering the current consumption in our custom board. The board has the following components (my FW view :)
nRF9160 - powered directly from batteries (either...
Hi
I use nRF7002-DK and sdk version as v2.5.2,download lesson8 exercise 3 solution and build was error as below log, which parts am I miss?
build config as below
...
Hello,
I a working on a project that uses the nRF5340 CCM peripheral (Network core) in an asynchronous mode. That is, I encrypt PDUs prior to scheduling them for transmission...
I want to configure my setup for secure boot and enable TFM and encrypted application images for firmware update. I am using nRF sdk version 2.5.0. My board is nRF9160. Now...
I have setup the UART along the same lines as the sample project in the DevZone Academy. I have extended the example provided to suit the project needs.
What I am getting...
In our custom board nrf5340-nrf7002, tried system_off(C:\ncs\v2.6.1\zephyr\samples\board\nrf )sample to check power consumption.
But it measures 0.60mA Is there any config...
Hi all, We have a custom board running with a project based with ncs v2.6.0. On our board we have two external flash, one is used for DFU the mcuboot_secondary with QSPI and...