I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
hello
I used nrf52840 with SDK15.3.
1.I use the example in this ticket and adjusted the baud rate to 9600 without hardware flow control. After SES is compiled, an "NRF_ERROR_SVC_HANDLER_MISSING...
MM8130-2600RA2
https://www.digikey.in/en/products/detail/murata-electronics/MM8130-2600RA2/1775922
This is RF connector used in DK. Please provide us the mating...
Hi there.
I am currently learning mqtt_simple from the nrf sdk example. So, I was trying to create a hex file that build using nrf9160, because I can't build it on thingy91...
Hi,
I have a custom board which uses P0.02 and P0.03. They are connected to interrupt signals from external devices.
To configure them as GPIO I set CONFIG_NFCT_PINS_AS_GPIOS...
Hi
I am developing a custom board using nrf9160. But before jumping to that process, I am using thingy91 (nrf9160 chip) as evaluation board for check all the firmware works...
Does ZBOSS support manufacturer specific attribute extension to standard clusters?
How about implementation of manufacturer specific clusters?
Are there examples one can...
Hi,
iOS NRF Mesh 2.2.3 version is working, but 3.2.0 unable to connect nodes,
Please suggest the procedure with iOS version in details.
Regards,
ArpitA
I use nRF5_SDK_for_Thread_and_Zigbee_2.0.0_29775ac and pca10056 board.
I use project nRF5_SDK_for_Thread_and_Zigbee_2.0.0_29775ac\examples\zigbee\light_control\light_bulb...
Hello! I will start by saying that I am new to embedded software development, and new to nrf boards in general. After successfully running the direction finding connectionless...
Hi Nordic Team,
I got the board yesterday, so I tried to debug on it. it seems no image is downloaded before shipped to me, as no log at all after power on, right?
So...
I have the next system perfectly working:
nRF52840 working as NCP to get OpenThread protocol.
STM32L486 as a host with a FreeRTOS
The communication between both is...
As far as I can see, when sending data via Bluetooth, the data is first stored in the buffer and then sent out together when the buffer is full. Is this the right idea? But...
Hello, We have an nRF9160 based IoT device in the pipeline, which should now be tested in a certified test lab. The purpose would be to perform a spurious emissions test using...
Good Day
I have enabled power saving on my nrf9160dk and am using NBIOT. In doing so I found that there was a 60 sec offset to what I selected and what I wanted the active...
