I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
I have started working with the nFR9151-DK board. After some time, I may have accidentally erased all data from the board using the PROGRAMMER application. As a result, the...
hi Nordic
i am working with nrf52840 and nrf52832 with ncs v2.8.0
i am also working on nrf54l15 (since nrf54h20 seems to not be fully integrated yet)
i want to know...
Hi,
I am trying to do t rilateration using one initiator and 3 reflectors. For now I am just trying to get 2 reflectors to work.
Sadly I cannot get the initiator to...
hi support team,
may i ask how to test 54l15+21540 dtm? i have send code to customer, but they feedback to me that the output power is 15db, not 20db(using serial send command...
Hello,
The customer, T&D would like to registrate their product to Bluetooth SIG.
Then, design number shoule be required, however, regarding SDK3.0.2, there isn't any...
I am working on an nRF54L15 project and started from: C:\ncs\v3.0.2\nrf\samples\bluetooth\peripheral_uart as the base. I would like to trigger an interrupt once every second...
In the reference schematic design of the 54L, why does the RF circuit use three LC circuits? What is the purpose? This approach would likely result in higher insertion loss...
I have made a PCB using a BL5340PA module, to start i have tried a simple code to see log from RTT using the SWD SWCLK pin, i am using an NRF5340 DK as debugger/programmer...
Hi apparently the examples are not working out of the box. I do not see any documentaiton on what has to be done for them to work. Can you advise me on what i shoud do to...
This table for the absolute maximum ratings isn't clear.
Can you help confirm the unit "y" here for RRAM retention? Is this years? Is it cumulatively years or consecutive...
I am experiencing an issue with my nRF52840 DK board. When I initially connect the board to my PC via USB, the debugger LED (LED5) blinks briefly but then turns off. Additionally...
Hi,
I'm looking for some guidance.
I'm using a HolyIoT nRF54L15 dev kit to evaluate their nRF54L15 module.
I am currently looking power consumption.
I have tried the...
I'm wanting to repetitively read the SPI buffer as a master to check a status bit. I figure there's no sense in using the DMA when I can read the SPI RXD buffer directly....
