I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
I am searching for a straight answer to this question. 'Application event' is used frequently in the documentation but never defined. I write the application but I clearly...
I use nRF52832 as a central device. I also use ble_app_uart_c as a SDK(17.0.2) . I would like to connect my peripheral which is my phone(iPhone 6) and i want to see my phone...
Hi,
I'm on pre-product of BLE Advertisement packet scanner.
My product is gathering the adv packets from a bunch of BLE tag about 20~30 tags.
So, I use two nRF52832...
Hi,
I want to add bonding information manually.
1.can I assume IRK key will be constant for multiple peripherals?
2.if IRK only key is available, can i add it to peer...
I am finding that the voltage measurement is about .52 volts off when measuring Vdd I have set up a power supply and connected it to external power. My saadc is set up with...
Hi,
I am starting to finalize a development stage and was looking at the current consumption of my device. I noticed, that when something connects to it and is starting...
Hello there,
we get the following assert:
"00> <t: 480881>, app_error_weak.c, 98, Softdevice assert: 88996:0"
The board is rebooting constantly after 3 ... 7 minutes...
I tried to build the example project for UART serialization demo, "ble_app_hrs_pca10040_s132_uart". It failed with 3 errors, see attached image.
It is SDK 17 and SEGGER...
Product: nrf52840 DK
Softdevice: 17.0.2
Hello,
I would like to start with a very humble statement that I am new to this nrf52 SoCs and would appreciate any of your...
Hey everyone,
I am playing around with Nordic Cloud, Thingy:91 with the Asset Tracker v1 and the Nordic Cloud RestAPI.
I happened to see in the process, that the unix...
Hello,
I contact to you because a customer bought the development tool part number n RF52-DK, and one received the product, they noticed that there was on the box of the...
I use nRF52 DK as a central devices and i have also other nRF52 DK and use for a beacon. I would like to show my beacon's RSSI value on the UART Terminal(Realtek,Termite exc...
Hi,
I have done buttonless DFU in Custom board using NRF52832. My code with DFU is working fine in the nrf52832 Development kit. While I am trying in a custom board. My...
I'm developing for nRF52 DK
using SDK 17.02
Segger 5.10b
I'm developing a service to read pin 12 where I'll have a square wave signal of about 60Hz. When I tested my...
