Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
Hello!
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0, window11 pro]
I am using two nRF52840...
Hi,
I have ordered custom board based on nRF52840 SoC couple of times from JLCPCB and that included assembling as well. Unfortunately, 90% of the boards had floating aQFN...
Hi,
I'm using the Bluetooth sample called Central HIDS and want to develop a feature that stops BT scanning after a few minutes.
However, during development, I encountered...
Hello,
I have a question regarding the consumption of the nRF9161 DK board when it is under the following conditions: MCU on IDLE, modem off, wake on GPIOTE input (event...
Hello, I am wondering - Is it possible to program BL651 Bluetooth 5 with nRF52810 using pca10040 development board with nRF52832 on it and using
BLE HID Keyboard and Mouse...
Hi,
I recently started upgrading an nRF chip on old SDK to the latest nRF Connect. The device has only one button and currently uses a static passkey (written on the device...
Hi! Firstly I am somewhat new to developing on nordic chips so I'd like to apologise in advance or any silly mistakes or oversights I may have made. I am currently working...
I am using NCS 2.6.1 and have programmed a nrf52840dongle (USB Dongle) with the build result of nrf/samples/openthread/coprocessor
The problem I am having is that normally...
Hello,
I was able to setup nRF5340 Audio DKs as gateway and headset, test the USB audio input and enable the Walkie Talkie demo. But in both cases I'm using I2S/analog headset...
I want to use the signing script as mentioned Technical Documentation (nordicsemi.com) , however, with NCS, this script is not automatically being picked up during the build...
EDIT: I thought I had enabled RTT terminal output in this proejct, which I had not. Obviously this will have an impact on my problems sorrounding RTT terminal output. So I...
Dear all,
I used till now an application to route BLE data over serial port through the dongle USB nrf52840, SEGGER IDE and 1.9.2 nrf conneck. All works well.
Now I'm...
I would like to confirm how to make nRF5340 Audio stereo.
The nRF5340 Audio source is mono, and to make it stereo I believe that it is necessary to convert the data between...
I have a project that was building, but now on restarting VS Code, I cannot access the build configurations.
The list shows a configuration as present, but when I expand...
