nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I encounter this problem:
The radio_test application works correctly on the official nrf52840dk board, but cannot receive input commands on my custom product board.
However...
Hi,
I have been developing a PCB with an nRF9151 and a SKY65943-11 LNA among other ICs. I looked up the nRF9151 Development Kit (PCA10171) datasheet for some of the pinouts...
I am running a modified asset_tracker_v2 on a nRF9160. all is working fine. I am upgrading from SDK v2.5 to SDK 2.90. After a build I find the merged.hex file under the build...
Hi everyone,
I've purchased two nRF905 modules ( www.otronic.nl/.../nrf905se-draadloze-transceiver-met-antenne.html) . I want to establish communication between a Raspberry...
we used SDK V2.6.2,
we used external flash for the OTA,
when we do the OTA after the NVS flash is erase so how we can solve this,
we used nvs_storage for this,
EMPTY_0...
Hi.
After migration from SDK2.7.0 to SDK2.9.0 I have issues with power mangement. CONFIG_PM_DEVICE_RUNTIME=y, which I used, causes that twi driver doesn't start. I try to...
I am using a customized PCB (nrf52840) and I have been successfully set up the SPI communication in between the nrf and lsm6dso
I used 0.11 as clk , 0.27 as MISO and 0.25...
Hello. We are testing nrf5340 - nrf7002 using the example of blpovisioning. I try to put on/off function using button, but if I reset pcb and turn on, it will connect to wifi...
I have our app on the nRF7002-DK board running with MCUboot configured for USB firmware updates. That is working fine, but is there some way to enable the console output from...
Hello.
I have been successfully flashing the nrf52840 dongle using the nrfjprog comand. I have been successfully able to reset and erase as well. Recently however, none...
I'm facing issues with my brand new PPK2 tool What I've done so far, my setup : * Ubuntu, linux * I installed latest nrf connect application from official * Installed Power...
Hello,
I've been using nRF54L15-DK devboard (0.9.2 revision on the label) for about a month now without any problems until today.
I wanted to change VDD output voltage...
We are developing a system were we rely heavily on the use of LWM2M. Using the provided LWM2M client we normally dont experience any problems at all and are able to establish...
We're experiencing issues with RTT logging on an nRF9151-based project using NCS 2.9.0. When `CONFIG_LOG_DEFAULT_LEVEL` is set to `3`, RTT Viewer fails to connect to the device...
Hello, I'm building the sample Measure battery voltage on a custom board, and I have an error voltage: setup: -134 at runtime. The overlay file is configure as explained in...
