Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
Hi,
I can use .overlay file to change the device tree setting of the nrf52840dk_nrf52840.dts.
However, my Board only has 1 button so I hope to "remove" 3 of the 4 buttons...
This discussion has been locked. I don't know why? and I don't know how to get it back.
devzone.nordicsemi.com/.../cannot-read-max30003wing-board-using-spi-communication...
I have an Zephyr application on the nRF5340 that I've been working on. I can debug fine in SES without a boot loader. However, when I add MCUBoot into the mix then everything...
I have some code that runs on the application and network processors that uses NRF_RPC NRF_RPC_CBOR (similar to the entropy_nrf53 sample) to communicate during boot loading...
I'm trying to get setup to debug an application that uses both the app and net cores. For now I'm using the example nrf/samples/nrf_rpc/entropy_nrf53/cpunet. I'm trying: ...
I am migrating our mesh network stack to NRF 52840, which is based on 802.15.4.
I would like the code to be more efficient state machine so that I don't have to busy-wait...
Hi,
I am using the ble_blinky example as a template to develop my project, with nRF52832 and SDK 17.0.2.
My first goal is to reduce consumption, so I have changed the...
Hello,
i had a look at lwm2m_client_sample and it worked pretty well. Now my next step is to be able to send for example a 100 or 500 Bytes Payload from nRf9160 to Leshan...
Hi Karl,
Sorry, I inadvertently closed the issue.
In my understanding, with SW9 in position "VDD", VDD_nRF is about equal to VDD_HV, so the measurement should work. I...
Hi
Is there an example for BLE "Just Works" using the NRF Connect SDK for the peripheral device?
I am using a peripheral device without display and would like to allow...
Hi,
In our application we use a motor. In the case that the watchdog would trigger while the motor is running, we need to stop the motor. For this we need to set the PWM...
Hi, all,
At first, I have to say I am a newbie in programming for BLE. ^^"
I trying to development a cycling power meter, so I want to modify this CSCS example to...
Hello, Recently I tested and flashed the Zephyr program to the nrf52840DK, it works fine. While I flashed as usual last time, I saw the LED5 flashing and then the PC didn...
I would like to perform a OTA DFU in a nRF52840 DK using nrfutil. For that, I'm using the example that is in SDK/examples/dfu/secure_bootloader/pca10056_s140_ble in the target...
