Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
Hii,
I´m working with LTE IoT 4 Click, by Mikroe, that use a nrf9160.
I need to connect to network with my modem, but i have some erros. My goal is to communicate with...
...On a NRF5340, using NRF Connect 2.6.1 SDK and tool chain.
In our application, we need to select if NRF5340 device boots in ZIGBEE ROUTER role or ZIGBEE END DEVICE role...
I've written a custom manufacturing programming tool for ARM Cortex-M4 nRF52832 and nRF52810 devices. It uses a J-Link Plus USB programmer (J-Link V7.98g) and is implemented...
I am working with Zephyr RTOS and I would to prepare one of my RAK4631 with a Zephyr bootloader.
I know that in the RAK4631 documentation we have instructions how to flash...
Hello,
By using nRF Connect SDK v2.6.1, I want to have RTC (Date Time, Calender, etc) functions, so I modified the code based on one of Nordic Academy examples, which can...
Hi,
I've resumed working on my project with the nRF Connect SDK after a brief break. However, when I try to run a simple project, I occasionally encounter an error while...
Hello, I've recently purchased an npm1100-EK schematic from Digikey. The evaluation board works great but I can't find the Schematic & hardware files for this particular version...
Hi everyone. I'm using nRF Connect SDK 2.6.1. I'm implementing LittleFS for file management on an external QSPI-Flash. I need to format the flash and erase all of data. I...
Hello,
I am currently researching the best way to be able to change the rate at which I fetch a GPS fix. I want to start the program at 60 seconds, then depending on environmental...
This is a continuation of this question . It may be necessary reading to understand the context.
I 'm confused by this topic too, however I think the error about "boot_partition...
Hi,
I'm trying to build the MQTT sample for a custom board, trying to communicate between nrf52840 and nrf7002 via QSPI. Here's my board definition:
In the build configuration...
Hello everyone,
I Have a LTE reconnection issue after LTE signal loss with SDK 1.3.6. I was doing some LTE connectivity tests by placing the board in a faraday box. After...
Hello! We have developed a custom board featuring an nRF9160 and an ESP32-C3-MINI-1 co-processor, which is flashed with AT-firmware (version 3.2.0.0). Our current application...
Good morning, if I wanted to develop a board with the VM3011 device, where can I find it? It seems impossible to find it as a device in major stores, and I can't even find...
