Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
I build contact sensor example (use nrf connect sdk v3.2.1, nrf52840 chip) and try commissioning with apple home kit (use homepod mini), device commissioning succeed but cannot...
Hello! I'm currently working on a circuit design where weight and size are critical factors. Could you please tell me the minimum dimensions and weight of this chip? Thank...
I've made a new project as I had to change some hardware than the previous one.
The code seems fine, but I'm not able to load the libraries in the project.
A red underline...
When an ESD shock to the PCBA causes the nrf52840 to reboot, what reset code should we expect to show up with hwinfo_get_reset_cause()? RESET_BROWNOUT?
Using Zephyr NCS...
Hi! I am trying to use the LE Audio application and one of the samples in it, by including the necessary source files, and Kconfigs in my project. On the network core, I am...
As per the doc , when I use a smartphone (the base version is Android 12) to touch the NFC antenna, I should see a pop-up window:
3.Confirm pairing with ‘Nordic_HIDS_keyboard...
Is it possible to promote my project here: complete Zephyr development environment running solely on Raspberry Pi 4 Bookworm OS? If nothing else it does provide information...
Hi There,
During the transmission and reception performance test, I found that the LE1M's maximum sensitivity was only -92 dBm, while the LE2M's maximum sensitivity was...
Hi,
we have a Gateway board that uses the nRF52832 with the nRF21540.
The firmware running on the nRF52832 is a slightly modified version of the HCI UART sample found...
I have a problem with timer 3 of nrf52820.
It concerns a trailing edge dimmer implementation based on timer 3. A gpiote is used to sync the zero crossing.
I use ppi...
Dear Nordic-Team,
I designed a custom PCB using the nRF9151 as the host processor, the nRF7002 as a Wi-Fi companion, and the nPM1300 as the power management IC. The Wi-Fi...
Hello,
I encountered a strange behaviour on a nrf52832 : - I flash a a debug firmware (with debug optim in build config) : I can run debugger and add breakpoints - I stop...
I am developing an application that uses NCS2.8.0.
For FW updates, the nRF52833 USB ACM bootloader is enabled.
However, there are some problem.
My device has a battery...
Hi all hope you all are fine and doing well.
I am trying to use the Soft UART (uart-bitbang.c driver) on nRF52 DK for a low-speed UART connection. The initialization fails...
Hello, I am not sure if this is the most appropriate place to ask this question, but any comments are welcomed. I am developming a sensor platform that tries to use extended...
