NRF24AP2 with MSp430F149 . ASYNC 9600 N 8 1
step 1 : reset NRF24AP2 with reset pin , and received a pulsing signal through RTS pin
step 2: send a char (0x4A) to NRF24AP2...
Hi guys,
I am using the gcc setup to program my boards. However for flashing the softdevice I use nrfgoStudio. SO I downloaded the hex file and fashed the siftdevice. But...
How do you create hid information for a joystick and send it over BLE. Nordic doesn't seem to have
primitives for this (they have keyboard and mouse facilities). I'm working...
I use a PCA10001 board as peripheral role of heart rate service and it can be discovered by control panel. But as I download the experimental program of central role of hrs...
I'm reading the source for the nRF Toolbox app for Android 4.3 and comparing it to the Proximity Profile spec from the Bluetooth SIG, which has this to say about path loss...
Hello,
I have downloaded the software related with the "nRF51822 Bluetooth Smart Beacon Kit" in order to modify typical iBeacon's parametres such as UUID, Major ID, Minor...
Hello,
We have been using FDS in our nrf52832 based product. Recently we had a need to port application to nrf52810. It required some flash memory optimization. Fortunate...
Documentation states “When a connection is created it will inherit the transmit power from the initiator or advertiser leading to the connection.” In my BLE event handler...
Hi,
SDK16
I'm using ble_cus.c to define custom BLE service.
In the ble_cus.h file the definition of the UUID is
#define CUSTOM_SERVICE_UUID_BASE {0xBC, 0x8A, 0xBF...
Using just the nRF Connect SDK, I cannot get a push button to interrupt the NET CPU on the nRF5340DK.
I have the following code on the APP CPU:
nrf_gpio_pin_mcu_select...
L2CAP connection oriented channels can be used to transfer frames of up to 65533 bytes. L2CAP is a record oriented protocol. When receiving L2CAP data, using the softdevice...
I have purchased eval kit and entered bootloader mode by pressing BOOT/RESET button while powering up the device but haven't put any file but now when i power up the device...
Hi,
We are in a stage where we want to perform certification of a product and are now looking into an application that can be used to this end. The board is using SDK 15...
Hi,
I've bought a nRF52840-DK kit to evaluate a Nordic BLE SOC (we are interested in using the nRF52811). I've installed SEGGER Embedded Studio 4.52, and obtained a Nordic...
Hello, I am I'm a Beginner at developing NRF 51822. My Development Environment sdk : 12.3 IDE: KEIL v5 SoftDevices : s130
I am developing using the example of 'ble_app_uart...
Hi everyone,
I am trying to understand the Memory layout of nRF52840 SOC in order to apply RAM retention into specific section. Looking the memory layout at pg 21 of the...
Hello Nordic community,
I have a nrf52-DK with SDK15.2.0 and I'm trying to communicate with ST HTS221 sensor. I have the original STEVAL-MKI141V2 evaluation board.
I...
Hello,
I was wondering what examples we have in nRF Connect SDK (NCS) for firmware updates over BLE and serial (receiving an image from another device over UART). Specifically...
Hi
I have bought NRF5340-PDK board to study BLE-MESH. I found that there is 2 development tool in Nordic website
1. nRF connect SDK
2. nRF connect for Desktop
...
Hi,
I have a custom PCB that uses the nRF9160 and an RGB LED. I want to drive this LED with PWM but it uses an active LOW style of GPIO drive. I have been able to use normal...
